Open Access
17 March 2014 Effect of size of aluminum/silicon dioxide/aluminum nanosandwich films on their optical properties
Author Affiliations +
Abstract
Three aluminum (Al)/silicon dioxide (SiO 2 )/aluminum (Al) nanosandwich films (SWFs) of various heights were fabricated using glancing angle deposition. An SWF comprises a 45-nm thick SiO 2 layer sandwiched between two Al nanopillars. The thicknesses of both top and bottom nanopillars were varied from 187.5 to 217.5 nm. The equivalent constitutive and related parameters of each SWF were obtained from the reflection coefficients and transmission coefficients that were measured using a walk-off interferometer. Both the equivalent permittivity and the equivalent permeability of each SWF turned out to be negative real. Exactly how the height of the Al nanopillars of the double negative SWF affects its low reflectance through destructive interference is also examined using the wave tracing method. Moreover, the localized reversed magnetic field in the SiO 2 layer of each SWF was simulated by finite-difference time-domain method to qualitatively interpret the negative real permeability.

1.

Introduction

With the rapid development of metamaterials in the recent decade, related works have demonstrated the novel optical properties of subwavelength structures of such metamaterials, including the negative refractive index13—from microwave wavelengths to visible wavelengths. To achieve related applications (e.g., perfect lens and cloaking4), many recent efforts have attempted to reduce the loss of metamaterials.5,6 However, between the discovery of metamaterials and the development of metadevices, the mass production of metamaterials is of priority concern.7 In addition to electron-beam lithography,8 glancing angle deposition9 is a relatively facile means of coating a nanostructured thin film with a negative refractive index at visible wavelengths. By depositing at a glancing angle of 89 deg and deposition rate of 1nm/s, a slanted Ag nanorod array (NRA) with a thickness of 160 nm exhibits a negative real refractive index. Measurement results indicate that the polarization-dependent refractive index is positive real for s-polarization (i.e., the electric field of the incident wave oscillates normally to the rods) and negative real for p-polarization (i.e., the electric field of the incident wave oscillates along the rods). The p-polarized refractive index is 0.581 +i0.213, 0.307 +i1.621, and 0.389 +i1.816 at wavelengths λ of 532, 639, and 690 nm, respectively.10 However, the p-polarization transmittance of Ag NRA is only <5%, owing to its strong light absorption.

A previous work attempted to mitigate the loss problem of metal NRA by fabricating a sandwiched AlSiO2Al upright NRA was fabricated through the introduction of rapidly substrate spin during glancing deposition.11 This sandwiched NRA exhibits a polarization-independent negative refractive index and equivalent permeability for normal incidence. Additionally, loss of the sandwiched film is sufficiently low to allow light to propagate through and to be reflected back from, the film, subsequently producing interference effect. Antireflection caused by destructive interference from the film is observed and demonstrated herein. The negative phase change caused by backward wave propagation in a negative index medium contributes to the destructive interference between the first two orders of reflected waves.

This work examines how the Al nanopillar thickness affects electromagnetic and optical properties of the AlSiO2Al sandwiched. Three samples with Al nanopillar thicknesses varying from 187.5 to 217.5 nm are fabricated. Their electromagnetic parameters, including permittivity, permeability, and the bianisotropic parameter, are also derived from optical parameters, including refractive index, forward impedance, and backward impedance. The optical parameters are derived from the reflection and transmission coefficients measured by using walk-off interferometry. Moreover, the low reflectance values for different thicknesses of nanosandwich films (SWFs) are analyzed using the optical parameters. Furthermore, the negative real permeability variation with the size of SWF is investigated through simulation of the localized magnetic field, by using the finite-difference time-domain (FDTD) method. This work reveals that low reflectivity exists over an extended range of thickness of SWF with negative real index. The thickness-dependent optical parameters will be useful in optical thin film design for a novel optical filter that contains both positive and negative index thin films.

2.

Fabrication and Measurement

In the fabrication of SWF, SWFs were grown by glancing angle deposition (GLAD) technique in an electron-beam evaporation system. The chamber containing the substrates and the targets of aluminum and silicon dioxide was pumped to a base pressure of 4×106 Torr prior to evaporation. The target-to-substrate distance was fixed at 29 cm. The collimated vapor flux of either Al or SiO2 was directed toward the substrate at an angle of 89 deg to the substrate normal. The substrate spun around its central normal axis at a rate of 10 rpm, subsequently causing the growing film to comprise upright nanopillars. A quartz crystal microbalance was placed next to the stage to monitor the deposition rate, which was maintained at approximately 1nm/s. Figure 1 presents the top-view and cross-section views of the three SWFs. Table 1 lists the size parameters, including the average diameter and average thickness of each SWF.

Fig. 1

Top view and cross-sectional scanning electron microscopic images of three AlSiO2Al nanosandwich films (SWFs) with total thicknesses of (a) 420 nm, (b) 450 nm, and (c) 480 nm, respectively.

JNP_8_1_083994_f001.png

Table 1

Average diameter and thickness of each sample.

SampleTotal thickness of SWF (nm)Thickness of SiO2 layer (nm)Thickness of Al layer (nm)Average diameter (nm)
SWF-A42045.0187.5165.4
SWF-B45045.0202.5176.9
SWF-C48045.0217.5179.8

Figure 1 describes the system coordinates (x,y,z), as defined for optical measurements, where the z-axis is the direction of normal to the surface of the film. According to Fig. 2, the x(y)-polarized transmittance Tj, reflectance Rj, and absorbance Aj=1(Rj+Tj), j{x,y}, of the SWF depends slightly on the orientation of the electric field of normally incident light. Here, the spectra of both transmittance and reflectance are measured on a TRIAX 180 spectrometer (Horiba Jobin Yvon, Opticsvalley, France). The transmittance of all three samples increases with wavelength, and a thicker SWF exhibits lower transmittance. The transmittance of the 420-nm thick SWF increases from 0.312 at λ=400nm to 0.687 at λ=700m, while the transmittance of the 480-nm thick SWF increases from 0.263 at λ=400nm to 0.627 at λ=700nm. Although the thickness of SWF varies from 420 to 480nm, the reflectance levels of three samples are <1%.

Fig. 2

Measured spectra of the Tj, Rj, and Aj=1(Rj+Tj), j{x,y} of (a) SWF-A, (b) SWF-B, and (c) SWF-C and the average reflectance spectra of (d) SWF-A, (e) SWF-B, and (f) SWF-C. Light was normally incident for transmittance measurements, yet obliquely incident at 5 deg to the normal for reflectance measurements.

JNP_8_1_083994_f002.png

The equivalent refractive index Nj=Nj+iNj, equivalent relative impedance Z+,j=Z+,j+iZ+,j, and Z,j=Z,j+iZ,j are derived from reflection and transmission coefficients measured from both sides of the air/SWF/substrate system using a method described elsewhere.12 The equivalent relative impedances Z+,j=Z+,j+iZ+,j and Z,j=Z,j+iZ,j are associated with forward (+) and backward (−) directions of light propagating through the air/SWF/BK7 glass system (Fig. 1). The equivalent relative permittivity εj=εj'+iεj", equivalent relative permeability μj=μj+iμj, and bianisotropic parameter ξj=ξj+iξj are then calculated from Nj, Z+,j, and Z,j, respectively. Additionally, the complex-valued reflection coefficients r±,j and transmission coefficients t±,j of the SWF are measured for the SWF deposited on the glass slide, by using a walk-off interferometer with a wavelength-tunable 35 KAP 431-220 Ion Laser System (CVI MellesGriot, Albuquerque). The measurements are also taken at three wavelengths: 476, 568, and 676 nm. Figure 3 plots the values of Nj at the three wavelengths and Table 2 lists the values Z+,j and Z,j. Figure 4 presents the equivalent electromagnetic parameters and optical parameters of the three samples. The magnitude of the real part of the refractive index increases with wavelength, subsequently preventing the optical thickness varying intensively with wavelength. The imaginary part of the refractive index is sufficiently low to have interference between the first two reflected waves from SWF. The value Nj is within the range (0.117, 0.137) for SWF-A, (0.046, 0.073) for SWF-B, and (0.086, 0.098) for SWF-C. As the thickness of SWF increases from 420 to 480 nm, the equivalent refractive index is negative; in addition, its average magnitude decreases from 2.256 to 1.132 at a wavelength λ of 676 nm. Similarly, the real part of the equivalent permittivity varies from 1.193 to 0.824 as the thickness increases. Both equivalent permittivity and permeability are negative real, and the magnitude of the real part of the permeability increases as wavelength increases.

Fig. 3

Measured values of Nj for SWF-A, SWF-B, and SWF-C.

JNP_8_1_083994_f003.png

Table 2

Z+,j and Z−,j for SWF-A, SWF-B, and SWF-C.

SampleZ+,j+iZ+,jZ,j+iZ,j
λ (nm)x-polarizationy-polarizationx-polarizationy-polarization
SWF-A4760.896i0.2670.929i0.1940.389i0.0090.413i0.002
5681.135+i0.0891.070+i0.0610.638i0.2330.652i0.213
6761.278+i0.2601.192+i0.2400.547i0.2800.549i0.282
SWF-B4760.821i0.2890.857i0.2020.536i0.1060.544i0.105
5680.741+i0.1590.812+i0.0810.483i0.0870.487i0.086
6761.119+i0.1080.974+i0.0630.672i0.2230.682i0.211
SWF-C4761.251+i0.0031.304+i0.0520.337i0.2350.355i0.225
5681.387+i0.2471.500+i0.2950.318+i0.1490.332+i0.136
6760.905+i0.1640.916+i0.2540.564+i0.1380.570+i0.140

Fig. 4

Measured values of εj and μj for SWF-A, SWF-B, and SWF-C.

JNP_8_1_083994_f004.png

3.

Wave Tracing

An attempt is made to exploit the cause of low reflectivity by using the equivalent optical parameters Nx, Z+,x, and Z,x to calculate the phase change associated with propagation through SWF, reflection coefficient, and transmission coefficient at both interfaces. The wave propagating through the film is simulated for two cases: the SWF-A at a wavelength of 676 nm and the SWF-C at a wavelength of 476 nm (Fig. 5). With incident electric field amplitude of unity, the first-order reflected wave and second-order reflected wave interfere with each other, resulting in diminished total reflected wave. The total reflected wave becomes 0.104ei(103.59°)+0.144ei(79.79°)=0.041ei(88.44°) for SWF-A at a wavelength of 676 nm and 0.153ei(6.42°)+0.094ei(177.55°)=0.058ei(2.27°) for SWF-C at a wavelength of 476 m. Both cases perform well in terms of the destructive interference between the first two reflected waves from the SWF, owing to a low loss property of SWF. Owing to the negative real part of the refractive index, the phase associated wave propagation is negative as a result of backward wave propagation.9 The near-π phase differences between the first-order and second-order reflected waves at wavelengths of 476 and 676 nm come from the low dispersive optical thickness, as shown in Sec. 2. Although the magnitude of the first-order reflection coefficient of SWF-A than that of SWF-C, the lower loss of SWF-A increases the magnitude of the second-order reflection coefficient of SWF-A more than that of SWF-C. Therefore, both cases have similar destructive interference phenomena.

Fig. 5

Wave tracing for SWF normally illuminated by light with an electric field amplitude of unity for SWF-A at a wavelength of 676 nm and SWF-C at a wavelength of 476 nm.

JNP_8_1_083994_f005.png

4.

Magnetic-Field Reversal Analysis

The negative real part of the permeability arises from the reversal of the magnetic field between a pair of aluminum grains. According to the values in Fig. 4, the average real part of the permeability of SWF-A varies from 0.6684 at λ=476nm, 1.2878 at λ=568nm to 1.8588 at λ=676nm. Additionally, the average real part of the permeability of SWF-B varies from 0.6550 at λ=476nm, 0.9240 at λ=568nm to 1.5792 at λ=676nm. Moreover, the average real part of the permeability of SWF-C varies from 0.5361 at λ=476nm, 0.6183 at λ=568nm to 0.9240 at λ=676nm. When the thickness of SWF increases from 420 to 450 nm, the magnitude of negative real permeability decays about 2.0%, 28.2%, and 15.1% at wavelengths of 476, 568, and 676 nm, respectively. However, the magnitude of the negative real part of the permeability obviously decays when the thickness increases from 450 to 480 nm; in addition, the value drops about 18.2%, 33.1%, and 41.5% at wavelengths of 476, 568, and 676 nm, respectively.

Reversal of the magnetic field in the SWF is induced by coupling in the dielectric layer of the antiphase electric fields that oscillate in the top and bottom nanodisks. Also, the magnitude of the negative real part of the permeability is proportional to that of the magnetic dipole moment. The magnetic response of individual sandwiches is simulated by the FDTD method for a sandwich model. The sandwich model consists of coaxial Al nanodisks, separated by a cylindrical SiO2 spacer with a thickness of 45 nm. Since the diameter of the deposited Al nanopillar is a Gaussian distribution judged from the top-view SEM image, the diameter of Al nanodisk for simulation is varied over a range from 100 to 220 nm. The thickness of Al nanodisk is adopted, as determined by the average thicknesses of the three samples. Figure 6 plots the reversed magnetic field along the y-axis at the center of the spacer versus wavelength from 400 to 700 nm and the diameter of SWF ranging from 100 to 220 nm. Simulation results indicate that the reversal of the magnetic field occurs over the visible wavelengths when the diameter exceeds 160 nm. In the simulation of SWF-A, magnitude of the reversed magnetic field is the largest at a wavelength of 700 nm with the diameter of 180 nm. The other two simulations for SWF-B and SWF-C have the largest reversal magnetic fields at a wavelength of 642 and 681 nm, respectively. In the three simulations, the average magnitude and area of the reversed magnetic field gradually decay as the thickness of SWF increases. Especially for the simulation of SWF-C, the area of the reversed magnetic field obviously shrinks obviously. Results of the FDTD simulation correlate with those of the detected spectra of permeability.

Fig. 6

Simulated intensity of reversed magnetic field Hy as a function wavelength (vertical coordinate) and sandwich diameter (i.e., transverse coordinate) for (a) SWF-A, (b) SWF-B, and (c) SWF-C. Thickness of SiO2 film is 45 nm. (d) The inverse magnetic field Hy in middle layer of SWF oscillating in a manner opposite to that of the applied magnetic field (blue region).

JNP_8_1_083994_f006.png

5.

Conclusion

SWFs of various sizes are fabricated, along with their transmittance, reflectance, and absorptance compared as well. Although the absorptance increases with the SWF thickness, three samples with thicknesses of 420, 450, and 480 nm exhibit reflectance levels below 1%. The retrieved equivalent refractive index, forward impedance, and backward impedance reveal the propagation of the wave through SWF. Destructive interference for antireflection occurs even when the thickness of SWF is 480 nm. The dispersion of refractive index causes the low dispersion of optical thickness, resulting in destructive interference over the visible wavelengths. The decrease in measured negative equivalent permeability along with the thickness is interpreted qualitatively by simulating the reversed magnetic field at the center of each SWF. Simulation results indicate that the negative permeability arises from the reversal of the magnetic resonance within the SiO2 layer. Furthermore, the reversed magnetic field becomes weaker as the thickness of Al increases, which corresponds to the trend of measured negative real part of the equivalent permeability.

Acknowledgments

The authors would like to thank the National Science Council of the Republic of China, Taiwan, for financially supporting this research under Contract Nos. NSC 99-2221-E-027-043-MY3 and NSC 102-2221-E-027-096-MY3.

References

1. 

V. M. Shalaevet al., “Negative index of refraction in optical metamaterial,” Opt. Lett., 30 (24), 3356 –3358 (2005). http://dx.doi.org/10.1364/OL.30.003356 OPLEDP 0146-9592 Google Scholar

2. 

A. V. Kildishevet al., “Negative refractive index in optics of metal-dielectric composites,” J. Opt. Soc. Am. B, 23 (3), 423 –433 (2006). http://dx.doi.org/10.1364/JOSAB.23.000423 JOBPDE 0740-3224 Google Scholar

3. 

G. Dollinget al., “Simultaneous negative phase and group velocity of light in a metamaterial,” Science, 312 (5775), 892 –894 (2006). http://dx.doi.org/10.1126/science.1126021 SCIEAS 0036-8075 Google Scholar

4. 

J. Valentineet al., “Three-dimensional optical metamaterial with a negative refractive index,” Nature, 455 (7211), 376 –379 (2008). http://dx.doi.org/10.1038/nature07247 NATUAS 0028-0836 Google Scholar

5. 

S. Xiaoet al., “Yellow-light negative-index metamaterials,” Opt. Lett., 34 (22), 3478 –3480 (2009). http://dx.doi.org/10.1364/OL.34.003478 OPLEDP 0146-9592 Google Scholar

6. 

C. García-Mecaet al., “Low-loss multilayered metamaterial exhibiting a negative index of refraction at visible wavelengths,” Phys. Rev. Lett., 106 (6), 067402 (2011). http://dx.doi.org/10.1103/PhysRevLett.106.067402 PRLTAO 0031-9007 Google Scholar

7. 

N. I. ZheludevY. S. Kivshar, “From metamaterials to metadevices,” Nat. Mater., 11 (11), 917 –924 (2012). http://dx.doi.org/10.1038/nmat3431 NMAACR 1476-1122 Google Scholar

8. 

A. V. Kildishevet al., “Negative refractive index in optics of metal-dielectric composites,” J. Opt. Soc. Am. B, 23 (3), 423 –433 (2006). http://dx.doi.org/10.1364/JOSAB.23.000423 JOBPDE 0740-3224 Google Scholar

9. 

A. LakhtakiaR. Messier, Sculptured Thin Films: Nanoengineered Morphology and Optics, SPIE Press, Bellingham, WA (2005). http://dx.doi.org/10.1117/3.585322.ch5 Google Scholar

10. 

Y.-J. JenC.-H. ChenC.-W. Yu, “Deposited metamaterial thin film with negative refractive index and permeability in visible regime,” Opt. Lett., 36 (6), 1014 –1016 (2011). http://dx.doi.org/10.1364/OL.36.001014 OPLEDP 0146-9592 Google Scholar

11. 

Y.-J. Jenet al., “Metal/dielectric/metal sandwich film for broadband reflection reduction,” Sci. Rep., 3 1672 (2013). http://dx.doi.org/10.1038/srep01672 SREOA7 0474-781X Google Scholar

12. 

C. É. Kriegleret al., “Bianisotropic photonic metamaterials,” IEEE J. Sel. Top. Quantum Electron., 16 (2), 367 –375 (2010). http://dx.doi.org/10.1109/JSTQE.2009.2020809 IJSQEN 1077-260X Google Scholar

Biography

Yi-Jun Jen is professor and chairman of the Department of Electro-optical Engineering in National Taipei University of Technology (NTUT), Taiwan. He received MS and PhD degrees from the Institute of Optical Sciences of National Central University in 1994 and 2001, respectively. He joined the Department of Electro-optical Engineering, NTUT in 2002. His current research interests primarily involve fabrication of novel optical devices based on anisotropic thin films, optical property analysis for subwavelength scale composite material.

Hung-Sheng Liao received the BSc degree in the Department of Electro-optical Engineering at the Minghsin University of Science and Technology, Taipei, Taiwan, in 2009. He received the MSc degree from the Department of Electro-optical Engineering at the National Taipei University of Technology, where he is studying anisotropic optical analysis and nanosculptured thin films.

Meng-Jie Lin received the BSc degree in the Department of Electro-optical Engineering at the National Taipei University of Technology, Taipei, Taiwan, in 2008. He is currently pursuing the MSc degree and PhD degree in the Department of Electro-optical Engineering at the National Taipei University of Technology, where he is studying anisotropic optical analysis and optical property analysis for subwavelength scale composite material.

CC BY: © The Authors. Published by SPIE under a Creative Commons Attribution 4.0 Unported License. Distribution or reproduction of this work in whole or in part requires full attribution of the original publication, including its DOI.
Yi-Jun Jen, Hung-Sheng Liao, and Meng-Jie Lin "Effect of size of aluminum/silicon dioxide/aluminum nanosandwich films on their optical properties," Journal of Nanophotonics 8(1), 083994 (17 March 2014). https://doi.org/10.1117/1.JNP.8.083994
Published: 17 March 2014
Advertisement
Advertisement
KEYWORDS
Aluminum

Magnetism

Refractive index

Reflectivity

Optical properties

Transmittance

Destructive interference

Back to Top