Most common high power fiber lasers use large mode area (LMA) fiber to reduce unwanted non-linearity. Such fibers
usually guide few modes but operate close to single mode regime (underfill condition) for best beam quality. For packaging
considerations or for high order mode filtering, coiling the gain fiber is mandatory. Determining the best coiling architecture
may look simple but extra care must be taken when dealing with few moded LMA fiber.
We present a formalism to quantitatively express the adiabaticity of an optical fiber coil based on the normalized coupling
coefficient betweens modes. The goal is to evaluate the capability of a coiling system to preserve the modal repartition of
the optical intensity and preserve beam quality at fiber output. We present typical coiling configurations as examples.
A simple interferometric measurement setup is proposed to study figures of merit of a coil.
A new method is presented for the analysis of the modal content of a beam travelling in a waveguide. This method uses a
simple optical set up to record beam images. Depending on the application, the source can be broad band (BBS) or a
tunable laser. The method uses the eigenmode profiles of the waveguide under test, either theoretical or experimental
ones. In this case, the technique is applied to characterize the modal content of few moded large mode area (LMA)
fibers. Such LMA fibers are typically used in high power fiber lasers and amplifiers to reduce sensitivity to non-linear
effects. By calculating the scalar products of the unfolded experimental and theoretical 2D profiles, the modal content is
obtained. Access to such cost effective and easy to implement diagnosis tool will greatly help improving modal quality
preservation in components and systems based on the fundamental mode operation of few moded LMA fibers. The high
precision and performance of the method is evaluated using both computer generated and experimental data sets.
As overall power increases in fiber lasers and amplifiers, the amount of optical power which must be dealt
with in order to obtain high core to core and core to cladding isolation also increases. This unwanted light
can represent hundreds of watts and must be managed adequately. By combining a proper termination (end
cap) design and cladding stripping techniques it is possible to obtain a robust output beam delivery
component. The cladding stripping techniques are inspired by previous work done on high power cladding
strippers. All measurement presented here are done with a flat end cap. Both core to core and core to
cladding isolation will be better with an angled end cap. A core-to-core isolation of over 25dB was
measured, while core to cladding was over 30dB. Power handling was characterized by the capability of
the device to handle optical power loss, rather than transmitted power. The component dissipated over 50
watts of optical power due to isolation. The above results show that understanding the mechanisms of
optical loss for forward and backward propagating light in a end cap and the heat load that these losses
generate is the key to deliver kilowatts of optical power and protect the integrity of the system.
High-power combiner designs (such as kilowatt-class combiners and beyond) are increasingly aggressive on brightness
conservation in order to reduce the brightness loss of the pumps as much as possible in both direct diode combining
and pump and signal coupling, especially with the advent of next-generation high-power pumps. Since most of the pump
loss is due to brightness loss across the combiner, tighter designs (close to the brightness limit) are considerably more
sensitive to variations in the input power distribution as a function of numerical aperture; for instance, next-generation,
high-power multi-emitter pumps are likely to have larger numerical apertures than conventional single-emitter diodes. As
a consequence, pump insertion loss for a given combiner design sitting close to the brightness limit should be dependant
on the input power distribution. Aside from presenting a manufacturing challenge, high brightness combiners also imply
more sophisticated testing to allow a deeper understanding of the loss with respect to the far-field distribution of the pump
inputs and thus enable the extrapolation of loss for an arbitrary, cylindrically symmetric radiant intensity distribution. In
this paper, we present a novel test method to measure loss as a function of numerical aperture (NA) fill factor using a
variable NA source with square-shaped far field distributions. Results are presented for a range of combiners, such as 7x1
and 19x1 pump combiners, with different brightness ratio and fiber inputs. Combiners violating the brightness conservation
equation are also characterized in order to estimate the loss as a function of input power vs. NA distribution and fill factor.
Most of the current large mode area (LMA) fibers are few-moded designs using a large, low numerical aperture (N.A.) core, which promotes mode coupling between core modes and increases bending losses (coupling with claddingmodes), which is undesirable both in terms ofmode area and beamquality. Furthermore, short LMA fiber lengths and small cladding diameters are needed to minimize nonlinear effects and maximize pump absorption respectively in high-power pulsed laser systems. Although gain fiber coiling is a widely used technique to filter-out unwanted modes in LMA fibers, coupling between modes can still occur in component leads and relay fibers. In relay fiber, light coupled into higher-order modes can subsequently be lost in the coiling or continue as higher-order modes, which has the overall effect of reducing the effective transmission of the LP01 mode and degrading the beam quality. However, maximum transmission of the LP01 mode is often required in order to have the best possible beam quality (minimal M2). Launching in an LMA fiber with a mode field adapter (MFA)1 provides an excellent way of ensuring maximum LP01 coupling, but preservation of this mode requires highmodal stability in the output fiber. Small cladding, low N.A. LMA fibers have the disadvantage of being extremely sensitive to external forces in real-life applications, which is unwanted for systems where highly sensitive mode coupling can occur. In this paper, we present a detailed experimental and theoretical analysis of mode coupling sensitivity in LMA fibers as a function of fiber parameters such as N.A., core diameter and cladding diameter. Furthermore, we present the impact of higher N.A. as a solution to increase mode stability in terms of its effect on peak power, effective mode area and coupling efficiency.
The ability to strip cladding light from double clad fiber (DCF) fibers is required for many different reasons, one example is to strip unwanted cladding light in fiber lasers and amplifiers. When removing residual pump light for example, this light is characterized by a large numerical aperture distribution and can reach power levels into the hundreds of watts. By locally changing the numerical aperture (N.A.) of the light to be stripped, it is possible to achieve
significant attenuation even for the low N.A. rays such as escaped core modes in the same device. In order to test the power-handling capability of this device, one hundred watts of pump and signal light is launched from a tapered fusedbundle (TFB) 6+1x1 combiner into a high power-cladding stripper. In this case, the fiber used in the cladding stripper and the output fiber of the TFB was a 20/400 0.06/0.46 N.A. double clad fiber. Attenuation of over 20dB in the cladding was measured without signal loss. By spreading out the heat load generated by the unwanted light that is stripped, the
package remained safely below the maximum operating temperature internally and externally. This is achieved by
uniformly stripping the energy along the length of the fiber within the stripper. Different adhesive and heat sinking
techniques are used to achieve this uniform removal of the light. This suggests that these cladding strippers can be used
to strip hundreds of watts of light in high power fiber lasers and amplifiers.
We present an all-fiber monolithically integrated fiber laser based on a custom tapered fused bundle pump combiner
with 32 inputs ports connected to a double clad gain fiber. The pump combiner is designed to provide high isolation
between signal and pumps fibers providing intrinsic pump protection. This configuration can generate more than 100W
of continuous wave (CW) laser light using single-chip multimode pumps enabling long term reliability.
Access to the requested content is limited to institutions that have purchased or subscribe to SPIE eBooks.
You are receiving this notice because your organization may not have SPIE eBooks access.*
*Shibboleth/Open Athens users─please
sign in
to access your institution's subscriptions.
To obtain this item, you may purchase the complete book in print or electronic format on
SPIE.org.
INSTITUTIONAL Select your institution to access the SPIE Digital Library.
PERSONAL Sign in with your SPIE account to access your personal subscriptions or to use specific features such as save to my library, sign up for alerts, save searches, etc.