In order to measure the 2-D velocimetry distribution without seed injection in the high-speed flow field of the engine, the 2-D HTV (hydroxyl tagging velocimetry) technique in the complex combustion field has been developed. The image processing method combining difference method with cross correlation method is presented. The background noise is suppressed by the difference method. The variable-template is used to perform cross correlation operation with experimental images, and the obtained correlation images is fitted with two-dimensional polynomial. Not only can the complex background interference be suppressed, but also can realize accurate extraction position of the tagging cross grid center.So the extraction accuracy is better than 0.25 pixels, when the image SNR is higher than 2. At the same time, based on Matlab software, the data processing program is written. The velocimetry distribution is gained by processing the experimental data in the flow field of the scramjet model. The speed calculation error is less than 5%, which meets the requirement of measurement accuracy of the system.
Stray light is the main noise source for planar imaging measurement technique, which can affect the accuracy of results directly. A method of Structured Laser Illumination Planar Imaging (SLIPI) was used to solve this issue. The key of SLIPI is periodic modulation of laser spatial intensity and implementation of post filtering algorithm. In this paper, cylindrical micro lens array was used to modulate the spatial intensity of laser periodically, which was compared with Ronchi ruling. The post filtering algorithm adopts phase-locked detection method. The signal results can be separated from the noisy image using only one measurement image by this method. SLIPI method has been used in Temperature Sensitive Paints measurement experiments. A diagnostic optical path combining cylindrical micro lens array and cylindrical mirror was designed for the need of surface light source irradiation. The results show that the method of SLIPI can be applied to most planar imaging measurement techniques, and the accuracy of two-dimensional parameter measurement can be further improved.
For the purpose of measuring the flow velocity in a scramjet test model, an special designed measurement system was established, including the strong vibration suppression, optical transport consideration, the movable device etc. The interference of the strong vibration to the velocity measurements was avoided by two ICCD cameras capturing the reference tag lines image and moved tag lines image together during an experiment. According to the tag lines image feature, data processing including correlation algorithm, data fitting by a Gauss function were used respectively to extract the positions of the reference tag lines and the moved tag lines. The velocity measurements were carried out at the isolation section and the cavity section. The results showed that the well SNR could be achieved in the H2/air combustion heating flow, but in the kerosene fuel combustion flow, the measurements images might be interfered by the strong OH background from the chemical reaction, and the signal intensity could be reduced due to the tag laser attenuation through the absorption by kerosene vapor. But when the combustor model was run at a low chemical equivalent, the interference could be suppressed to an accepted level.
KEYWORDS: Chemical species, Luminescence, Combustion, Liquids, Optical filters, Signal to noise ratio, Bioalcohols, Indium, Laser induced fluorescence, Signal generators
Nonlinear regime Two-line Atomic Fluorescence (NTLAF) is a promising technique for two-dimensional thermometry. A key challenge is seeding of indium atoms into flame. This work aims at investigating the mechanism of Indium LIF signal generation in a fuel-rich InCl3-ethanol premixed flame. Several types of images including natural emission of the flame itself, natural emission of CH, natural emission of OH, natural emission at 410 nm/451 nm of indium atom, and laser induced fluorescence at 410 nm/451 nm were obtained. The indium atom was generated in the flame front, and could survive in the post-flame zone for a while which is benefit for making NTLAF measurements. Further detail mechanism of fluorescence signals generation in InCl3-ethanol solution burning was investigated. The conclusion which probable to be drew is that to gain high NTLAF signals, the size of liquid droplets should be well controlled, neither to be too large nor to be gasified.
The OH can be generated from photo-dissociation of water in the gas phase, and the generated OH has served in tagging velocimetry using the time-flight method. The hydroxyl tagging mechanism has the advantages of non-seeding, kindly flow following character, but its application in the reaction region is limited for the fluorescence interference from nascent OH. In this paper, we explored the laser induced fluorescence spectrum of OH both from burning and photodissociation. A photo-dissociation laser induced fluorescence (PD-LIF) system with optical multichannel analysis instrument (OMA) for spectrum analysis was developed. Based on multichannel mechanism, the LIF spectrum of OH from photo-dissociation and burning were acquired simultaneously. The temporal spectrum profiles of dissociation OH both in flame and air were taken by varying the pump–probe delay. The normalized emission spectrum in flame showed a process of rotational relaxation while in air the spectrum was almost not changed. The fluorescence intensity was precisely proportional to the base states population, so we can get certain states that the OH from dissociation was predominant from the fluorescence intensity ratio of OH. This result can be further utilized for hydroxyl tagging velocimetry technology (HTV) which was less affected by burning OH.
With the concern of environmental protection and reducing the fossil fuel consumption, combustion processes need to be more efficient and less contaminable. Therefore, the ability to obtain important thermophysical parameters is crucial to combustion research and combustor design. Traditional surveying techniques were difficult to apply in a confined space, especially the physically intrusions of detectors can alter the combustion processes. Laser-based diagnostic techniques, like CARS, SVRS, PLIF and TDLAS, allow the in situ, non-intrusive, spatially and temporally resolved measurements of combustion parameters in hostile environments. We report here a new non-intrusive optical diagnostic technique, based on laser-induced thermal grating. Thermal gratings generated in NO2/N2 binary mixtures, arise from the nonlinear interaction between the medium and the light radiation from the interference of two pulsed, frequency-doubled Nd:YAG lasers (532 nm). This leads to the formation of a dynamic grating through the resonant absorption and the subsequent collisional relaxation. By the temporally resolved detection of a continuous wave, frequency-doubled Nd:YVO4 probe laser beam (671 nm) diffracted by LITG. The temporal behavior of the signal is a function of the local temperature and other properties of gas, various parameters of the target gas can be extracted by analyzing the signal. The accurate singleshot temperature measurements were carried out at different test conditions using a stainless steel pressurized cell, data averaged on 100 laser shots were compared with simultaneously recorded thermocouple data, and the results were consistent with each other. The LITG signal is shown to grow with increasing the gas pressure and is spatially coherent, which makes the LITG thermometry technique a promising candidate in high pressure environments.
The velocity components of the high temperature high speed flow produced by a simulative device were diagnosed by single-line hydroxyl tagging velocimetry. The simulative device was driven by H2/air combustion gas, worked like a shock tube, held about 10-ms. The HTV tagging lines were put after the exit of device, and the experimental images at flow’s different regions were acquired through changing the tagging lines’ positions corresponding to the exit of device. And the velocity components along the device axis on tagging lines were calculated from the images. The results indicated that the velocity values of the flow in compress region were much slower than those in expansion region. Between the flow’s first expansion and compress regions, the velocity values at center were higher than those at both sides, but in the flow’s second expansion region, the velocity values at center were slower than that at both sides.
Laser induced fluorescence has the potential to get two dimension temperature and concentration map in combustion. For understanding the fluorescence technology exactly, A detailed experiment has been developed to investigate the fluorescence spectrum. The time variation of spectrum is first presented by changing the pump-probe time delay. And this is followed by demonstrate the response of fluorescence to laser excitation. As showed by the experiment result, The intensity ratio of the (1, 1) and (0, 0) fluorescence band was varied both with time and the exiting laser line, we attribute this phenomenon to the difference rotational distribution of excited OH. And the new rule, which exciting a specific rotational level in the A2Σ(υ ' =1) excited state from two difference rotational levels in the X 2Π(υ " = 0) ground state, was experimental confirmed, and this will be a foundation to the future two line laser induced fluorescence thermometry.
Access to the requested content is limited to institutions that have purchased or subscribe to SPIE eBooks.
You are receiving this notice because your organization may not have SPIE eBooks access.*
*Shibboleth/Open Athens users─please
sign in
to access your institution's subscriptions.
To obtain this item, you may purchase the complete book in print or electronic format on
SPIE.org.
INSTITUTIONAL Select your institution to access the SPIE Digital Library.
PERSONAL Sign in with your SPIE account to access your personal subscriptions or to use specific features such as save to my library, sign up for alerts, save searches, etc.