Mr. Kai-Yin Cheung Profile

Kai-Yin Cheung

at Univ of Hong Kong

SPIE Involvement:

Author

Publications (2)

This will count as one of your downloads.

You will have access to both the presentation and article (if available).

DOWNLOAD NOW

This content is available for download via your institution's subscription. To access this item, please sign in to your personal account.

Email or Username Forgot your username?

Password Forgot your password?

Show

Keep me signed in

No SPIE account? Create an account

Proceedings Article | 4 September 2009 Paper

Effect of fabrication processes on bulk heterojunctions (BHJ) photovoltaic device performance

W. Wong, C. Ho, M. Fung, Z. He, W. Chan, X. Wang, C. Yip, A. Djurisic, K. Cheung

Proceedings Volume 7416, 74161A (2009) https://doi.org/10.1117/12.825062

KEYWORDS: Solar cells, Photovoltaics, Polymers, Electrodes, Heterojunctions, Platinum, Aluminum, Organic photovoltaics, Magnesium, Roads

Read Abstract +

Organic photovoltaic (OPV) devices have attracted much interest in recent decades because they have a great potential for low cost solar cells. Among different kinds of organic solar cells, conjugated polymer/fullerene bulk heterojunction (BHJ) solar cells have exhibited improvements in the power conversion efficiency (PCE) in recent years. The performance of BHJ solar cells is highly dependent on different fabrication processes. To address this issue, we focus on the dependence of different photovoltaic parameters on the fabrication methods. BHJ solar cells fabricated using platinum metallopolyyne (P1) with a low band gap of 1.85 eV as an electron donor and phenyl-C61-butyric acid methyl ester (PCBM) as an electron acceptor have been studied. The fabrication parameters, such as ratios of P1 to PCBM, solvents used, thickness of the active layers and top contact materials, have been systematically investigated. Blend ratio and solvent used had most significant influence on photovoltaic performance with several times higher efficiency of the best condition compared to the worst condition. They affected all photovoltaic parameters [open circuit voltage (V_oc), short circuit current density (J_sc) and the fill factor (FF)]. Top contact materials affected the V_oc and the FF, while thickness of the active layer mainly affected the J_sc and FF. The influence of different fabrication conditions on photovoltaic performance has been discussed.

Proceedings Article | 17 October 2007 Paper

Titania nanotube array based photovoltaic cells

W. K. Chan, A. B. Djurišić, K. Y. Cheung, C. T. Yip

Proceedings Volume 6656, 665616 (2007) https://doi.org/10.1117/12.732762

KEYWORDS: Annealing, Dye sensitized solar cells, Titanium, Crystals, Solar cells, Electron transport, Temperature metrology, Transmission electron microscopy, Nitrogen, Scanning electron microscopy

Read Abstract +

It has been shown that dye sensitized solar cells (DSSCs) based on porous titanium dioxide (titania) layers have efficiencies exceeding 10%. Although porous structure has the advantage of large surface area for light harvesting, electron transport through the random nanoparticle network forming a porous film results in electron mobilities which are two orders of magnitude lower compared to the single crystal materials. Therefore, considerable efforts have been made to fabricate DSSC based on one dimensional nanostructures, such as nanowires or nanotubes. Titania nanotube arrays are typically made by anodization of titanium, followed by annealing to improve crystallinity. In this work, we investigated the influence of annealing temperature and annealing atmosphere on the crystal structure, the electron transport, and the solar cell performance of titania nanotube arrays. The titania nanotube arrays were prepared from electrochemically anodized titanium foils and their morphology and crystal structure were characterized by scanning electron microscopy and transmission electron microscopy. The crystal phases and the compositions of nanotube arrays were further investigated by X-ray diffraction for different annealing temperatures and X-ray photoelectron spectroscopy for different annealing atmospheres. For optimal annealing conditions, the short circuit current density of 4.27 mA/cm² and power conversion efficiency of 1.30% could be achieved under AM 1.5 simulated solar irradiation for 2 μm long nanotubes.

My Library

You currently do not have any folders to save your paper to! Create a new folder below.

Folder Name

Folder Description

View contact details

UPDATE YOUR PROFILE

Is this your profile? Update it now.

Sign into your SPIE.org account

Don’t have a profile and want one?

Create an account on SPIE.org

Access to the requested content is limited to institutions that have purchased or subscribe to SPIE eBooks. You are receiving this notice because your organization may not have SPIE eBooks access.*

*Shibboleth/Open Athens users─please sign in to access your institution's subscriptions.

To obtain this item, you may purchase the complete book in print or electronic format on SPIE.org.

ORGANIZATIONAL
Sign in with credentials provided by your organization.

Organizational Username

Organizational Password

Show/Hide Password

INSTITUTIONAL
Select your institution to access the SPIE Digital Library.

SELECT YOUR INSTITUTION

PERSONAL
Sign in with your SPIE account to access your personal subscriptions or to use specific features such as save to my library, sign up for alerts, save searches, etc.

PERSONAL SIGN IN

No SPIE Account? Create one

PURCHASE THIS CONTENT

SUBSCRIBE TO DIGITAL LIBRARY

50 downloads per 1-year subscription

Members: $195

Non-members: $335 ADD TO CART

25 downloads per 1 - year subscription

Members: $145

Non-members: $250 ADD TO CART

PURCHASE SINGLE ARTICLE

Includes PDF, HTML & Video, when available

Members:

Non-members: ADD TO CART

Keywords/Phrases

Search In:

Publication Years