Dr. Markus Wimplinger Profile

Dr. Markus Wimplinger

Director of Technology for North America at EV Group

SPIE Involvement:

Author

Publications (7)

Proceedings Article | 9 April 2024 Presentation + Paper

Characterization and mitigation of local wafer deformations introduced by direct wafer-to-wafer bonding

Richard van Haren, Suwen Li, Mart Baars, Blandine Minghetti, Leon van Dijk, Ivanie Mendes, Karine Abadie, Marie-Line Pourteau, Gaëlle Mauguen, Michael May, Viorel Balan, Frank Fournel, Laurent Pain, Thomas Plach, Gernot Probst, Markus Wimplinger

Proceedings Volume 12956, 1295606 (2024) https://doi.org/10.1117/12.3010477

KEYWORDS: Wafer bonding, Semiconducting wafers, Distortion, Scanners, Silicon, Optical alignment, Deformation, Adhesion, Etching, Metrology

Read Abstract +

A new application in the semiconductor industry that received quite some traction the past few years is bringing the transistor power delivery network to the backside of the wafer. The big gain of this change is that it frees up real estate on the frontside of the wafer, enabling a further increase of the transistor density. This so-called Back-Side Power Delivery Network (BS-PDN) application is quite challenging since it requires a direct wafer-to-wafer bonding process module. To get access to the transistor from the backside, a device wafer needs to be flipped and bonded to a carrier wafer followed by an annealing step. After these processing steps, the original substrate of the device wafer is removed by grinding and etch steps. This will enable access to the transistors from the backside of the wafer. The wafer processing continues by conventional layer deposition, lithography and etch steps, this time on the flipped wafer. Unfortunately, the bonding process module that includes the actual direct wafer-to-wafer bonding step itself, will also introduce a distortion in the device layer that has been transferred to the carrier wafer. Since the on-product overlay requirement for the first exposed layer on the backside to one of the front-side layers is tight (<10-nm today and <<5-nm in the foreseeable future), a deep understanding of the origin of the distortion fingerprint after bonding is required. In our previous work, we presented a method to isolate the distortion fingerprint due to bonding from the remaining other overlay contributors. The fingerprint we observed after linear corrections had a typical magnitude ranging from 50 to 80-nm. A clear 4-fold symmetry was observed that could be attributed to the crystal orientation of the (100) silicon substrate. We demonstrated that the scanner wafer alignment model is very capable of correcting the global 4-fold wafer distortion fingerprint. Residual levels of less than ~15-nm were shown. These residuals could be further reduced by applying a correction per exposure (CPE) recipe. We showed that performance levels of less than ~6-nm (99.7%) and ~10-nm (max) could be achieved after a 33-parameter per exposure field self-correction. The resulting wafer plots nicely revealed how to improve the overlay performance further. An increased level of residuals was found in the wafer center and at the wafer edge. In the current paper, we build upon our previous work and continue the investigation on the remaining overlay contributors that were identified previously. This time, the focus will be on the local wafer deformations that are visible after the direct wafer-to-wafer bonding step. By local we mean the distortions that manifest themselves over a very short spatial range. These local distortions cannot easily be corrected by the scanner and are typically present close to the wafer center and the wafer edge. We know that the local wafer deformation close to the wafer center is caused by the bonding pin that initiates the bond wave. To characterize the center distortion signature, we varied many experimental parameters to see the impact. We will show the impact of the die layout, the rotation of the top wafer by a 45-degrees, wafer surface properties, and substrate choice of the carrier wafer. The latter is interesting, we evaluated both (100) and (111) carrier wafers. Although the prime focus will be to improve the overlay performance on the center of the wafer, we monitor the impact of the experimental settings on the wafer edge and remaining part of the wafer as well. We present a path forward to mitigate the local distortions such that they will not be blocking for high volume production.

Proceedings Article | 27 April 2023 Poster + Paper

Enabling layer transfer and back-side power delivery network applications by wafer bonding and scanner correction optimizations

Richard van Haren, Suwen Li, Blandine Minghetti, Leon van Dijk, Klaas Brantjes, Frank Fournel, Gaëlle Mauguen, Ivanie Mendes, Céline Lapeyre, Marie-Line Pourteau, Michael May, Laurent Pain, Karine Abadie, Thomas Plach, Markus Wimplinger

Proceedings Volume 12496, 124962C (2023) https://doi.org/10.1117/12.2657422

KEYWORDS: Wafer bonding, Semiconducting wafers, Scanners, Silicon, Distortion, Optical alignment, Transistors, Oxides, Crystals, Etching

Read Abstract +

Apart from the ever-continuing lateral scaling in the xy-plane to increase the transistor density, additional new concepts find their way to the semiconductor industry too. These concepts are based on making more use of the third dimension. One relatively simple idea would be to create a second layer of transistors to double the transistor density. However, the material requirements are high and the quality of the layer deposition by conventional Chemical Vapor Deposition (CVD) techniques is insufficient. Another application to free up real estate, enabling a smaller cell size and hence an increased transistor density, is to power-up the transistors from the backside. The power rails for logic devices are historically defined in the first Metal layer and consume quite some space. Bringing the power rails to the backside will free up space. However, access to the transistor layer from the backside of the wafer is far from trivial due to the presence of a 775-μm thick silicon substrate. The answer to the challenges mentioned above is wafer-to-wafer direct bonding. Although this technique is not new and already widely used in the semiconductor industry to manufacture CMOS Image Sensors (CIS), it currently finds its way to the high-end logic markets. In case of layer transfer, a crystalline silicon layer is created by bonding a Silicon-On- Insulator (SOI) wafer to the already existing device wafer. After the bonding step, the substrate of the SOI wafer will be removed leaving the crystalline silicon layer behind. Access to the transistor layer from the wafer backside can be enabled by wafer-to-wafer bonding as well. To this end, a completed device wafer will be bonded to an (un-patterned) carrier wafer. The substrate of the original device wafer will be removed, enabling access from the backside. Wafer-towafer bonding applications can only be enabled in case the induced wafer deformations are low or when they can easily be corrected during the subsequent exposures on the scanner. At CEA-Leti, a dedicated test vehicle process flow has been developed to characterize the wafer bonding-induced distortion fingerprints for both the layer transfer and the backside power delivery network applications. The wafer process flow has been simplified without losing the industry relevant on-product overlay challenges. Wafers have been created to enable an extremely dense characterization of the wafer bonding induced fingerprint. The methodology we applied enables us to isolate the wafer bonding induced distortion fingerprint, something that is difficult to do in a production environment. The Back-Side Power Delivery Network (BS-PDN) application is the most challenging one. The initial raw measured wafer distortion fingerprints are around 60 to 80-nm. These numbers can already be easily brought down by scanner corrections to ~15-nm (mean+3σ) without too much effort. However, these numbers are too large for the 2-nm technology node and beyond, and further improvement is required. The goal of this paper is to present the path forward to bring the bonding induced wafer distortion levels to 10-nm and below. We show the capability of the latest and greatest EVG bonding tool hardware and recipe settings available at the time of running the experiments in combination with the correction capability an ASML 0.33NA scanner.

Proceedings Article | 21 March 2017 Paper

Rules-based correction strategies setup on sub-micrometer line and space patterns for 200mm wafer scale SmartNIL process within an integration process flow

H. Teyssedre, S. Landis, P. Brianceau, M. Mayr, C. Thanner, M. Laure, W. Zorbach, M. Eibelhuber, L. Pain, M. Chouiki, M. Wimplinger

Proceedings Volume 10144, 101440V (2017) https://doi.org/10.1117/12.2260002

KEYWORDS: Semiconducting wafers, Nanoimprint lithography, Manufacturing, Critical dimension metrology, Lithography, High volume manufacturing, Calibration, Standards development, Etching, Silicon, Metrology, Scanning electron microscopy

Read Abstract +

Proceedings Article | 20 October 2016 Paper

Critical dimension uniformity characterization of nanoimprinted trenches for high volume manufacturing qualification

H. Teyssedre, S. Landis, C. Thanner, V. Schauer, M. Laure, W. Zorbach, L. Pain, S. Bos, M. Eibelhuber, M. Wimplinger

Proceedings Volume 10032, 100320M (2016) https://doi.org/10.1117/12.2250194

KEYWORDS: High volume manufacturing, Nanoimprint lithography, Semiconducting wafers, Critical dimension metrology, Silicon, Ultraviolet radiation, Polymers, Manufacturing, Metrology, Scanning electron microscopy

Read Abstract +

Proceedings Article | 18 March 2009 Paper

Industrial applications demanding low and high resolution features realized by soft UV-NIL and hot embossing

R. Miller, T. Glinsner, G. Kreindl, P. Lindner, M. Wimplinger

Proceedings Volume 7271, 72712J (2009) https://doi.org/10.1117/12.814102

KEYWORDS: Silicon, Materials processing, Polymers, Semiconducting wafers, Nanoimprint lithography, Lithography, Glasses, Ultraviolet radiation, Quartz, Manufacturing

Read Abstract +

Proceedings Article | 29 March 2004 Paper

Application of imprint technologies for creation of micro- and nano-scale pattern

Thomas Glinsner, Michael Beutl, Steven Dwyer, Paul Lindner, Markus Wimplinger, Paul Kettner, Samy Hanna, Gunther Leising

Proceedings Volume 5275, (2004) https://doi.org/10.1117/12.522993

KEYWORDS: Polymers, Nanoimprint lithography, Nickel, Positron emission tomography, Silicon, Lithography, Printing, Glasses, BioMEMS, Nanofabrication

Read Abstract +

Proceedings Article | 10 November 2003 Paper

Beginning-to-end wafer bonding for advanced optical systems

Shari Farrens, Paul Lindner, Steven Dwyer, Markus Wimplinger

Proceedings Volume 5177, (2003) https://doi.org/10.1117/12.507179

KEYWORDS: Semiconducting wafers, Wafer bonding, Microelectromechanical systems, Coating, Silicon, Adhesives, Compound semiconductors, Sapphire, Optical components, Lithography

Read Abstract +

Showing 5 of 7 publications

View contact details

UPDATE YOUR PROFILE

Is this your profile? Update it now.

Sign into your SPIE.org account

Don’t have a profile and want one?

Create an account on SPIE.org

Keywords/Phrases

Search In:

Publication Years