With the adoption of extreme ultraviolet (EUV) lithography for high volume production in the advanced wafer manufacturing fab, defects resulting from stochastic effects could be one of major yield killers and draw increasing interest from the industry. In this paper, we will present a flow, including stochastic edge placement error (SEPE) model calibration, pattern recognition and hot spot ranking from defect probability, to detect potential hot spot in the chip design. The prediction result shows a good match with the wafer inspection. HMI eP5 massive metrology and contour analysis were used to extract wafer statistical edge placement distribution data.
Proc. SPIE. 9778, Metrology, Inspection, and Process Control for Microlithography XXX
KEYWORDS: Copper, Electrons, Inspection, Scanning electron microscopy, Optical inspection, Wafer inspection, Semiconducting wafers, Chemical mechanical planarization, Back end of line, Defect inspection
We report an optical inspection guided e-beam inspection method for inline monitoring and/or process change validation. We illustrate its advantage through the case of detection of buried voids/unlanding vias, which are identified as yield-limiting defects to cause electrical connectivity failures. We inspected a back end of line (BEOL) wafer after the copper electro plating and chemical mechanical planarization (CMP) process with bright field inspection (BFI) and employed EBI to inspect full wafer with guidance of BFI klarf file. The dark voltage contrast defects were detected and confirmed as buried voids by transmission electron microscopy (TEM).
A novel classification methodology is constructed for Electron Beam (E-Beam) die-to-database (D2DB) inspection results on contact and via layers. It is a design guided defects classification flow that helps to pin-point true defects from a large amount of false alarm defects. Die-to-database E-beam inspection has remarkable features that can help find systematic defects such as Damaged Via and Missing Via; which will be reported as DVC (Dark Voltage Contrast) defects. However, the D2DB result usually reports millions of defects that lie on both ‘active via’ and ‘floating via’, the former being defects-of-interest (DOI), and the latter being of little significance. The indiscriminant mixture of DOI (on active vias) and nuisance (on floating vias) is a challenge in the use of D2DB for finding systematic via defects. We overcome this challenge by overlaying the E-beam defect location onto the design layout file (GDS or OASIS) and tracing the path of the via to determine whether or not it connects to the active or diffusion layer. Our proposed flow uses Net Tracing Classification (NTC) feature in Anchor Hotspot Solution (AHS) to classify all the reported DVC defects into different groups, according to the electrical connectivity of the contact. This classification involves multiple interconnected process layers. All the reported DVC defects will be classified into three groups: (1) Real DVC defects, in which the net traces down to active layer; (2) False DVC type 1, in which the net traces down to gate (which is always dark); (3) False DVC type 2, in which the net traces down to floating metal (which is always dark as well). This enhanced defect classification is greatly helpful in separating real DVC contact/via defects from false alarms. It has a secondary benefit of reducing the total number of defects, which is helpful for subsequent in-depth data analysis. In addition, the verified real DVC locations can be used to generate care areas for E-Beam die-to-die (D2D) inspection, which can effectively improve throughput and reduce the turn-around-time (TAT). In this paper, we will discuss a use case at the Vx layer.
We report an in situ formed tunable liquid microlense array and its applications for enhancing dynamic lab-on-a-chip performance. The de-ionized water microlenses are intrinsically formed via liquid-air interfaces of liquid droplets at T-shaped junctions of octadecyltrichlorosilane(OTS) treated polymerized isobornyl acrylate(poly(IBA)) microchannels., and can be separately tuned in focal lengths by pneumatic manipulation. Via the tunable microlenses, excitation light is dynamically focused onto the fluorescent fluidic sample, thus the fluorescence emission signal for detection is amplified. We have further shown the potential for surface reaction study at microfluidic interfaces by the microlense array.