Advanced lithography became possible using breakthrough technologies, including phase shift masks, advanced
illumination modes, aggressive OPC patterns and 193nm immersion optics. The Applied Materials Aera193 system, an
at-wavelength aerial reticle inspection tool, was introduced for the 90-65nm technology nodes. In the era of immersion
lithography and 55-45nm nodes, there is an increasing demand for Aerial inspection under immersion conditions. To
face this demand, the Aera193i was upgraded with expanded illumination and collection optics to support up to 1.4 NA
immersion conditions. Here, we describe novel Aerial inspection results under immersion conditions. We studied the
detection of a variety of defect types on 55nm node phase shift masks for immersion lithography. We found that the
immersion-emulation inspection was able to demonstrate a good detection line, with extremely low false alarms and
nuisance call rate. We also studied the relationship between Aerial defect detection and actual defect printability by
printing the same mask on wafer. We found good correlation between Aera193i detection line and actual defect
printability. We also address the polarization effects under immersion NA. We demonstrate that under polarized stepper
illumination the polarization effects on the image are negligible, while aerial imaging reliably emulates mask pattern
SCD has recently presented an uncooled detector product line based on the high-end VOx bolometer technology. The first FPA launched, named BIRD - short for Bolometer Infra Red Detector, is a 384x288 (or 320x240) configurable format with 25μm pitch. Typical NETD values for these FPAs range at 50mK with an F/1 aperture and 60 Hz frame rate. These detectors also exhibit a relatively fast thermal time constant of approximately 10 msec, as reported previously.
In this paper, the special features of BIRD optimized for unattended sensor applications are presented and discussed.
Unattended surveillance using sensors on unattended aerial vehicles (UAV's) or micro air vehicles (MAV's) , unattended ground vehicles (UGV's) or unattended ground sensor (UGS) are growing applications for uncooled detectors. This is due to their low power consumption, low weight, negligible acoustic noise and reduced price. On the other hand, uncooled detectors are vulnerable to ambient drift. Even minor temperature fluctuations are manifested as fixed pattern noise (FPN). As a result, frequent, shutter operation must be applied, with the risk of blocking the scenery in critical time frames and loosing information for various scenarios.
In order to increase the time span between shutter operations, SCD has incorporated various features within the FPA and supporting algorithms. This paper will discuss these features and present some illustrative examples.
Minimum power consumption is another critical issue for unattended applications. SCD has addressed this topic by introducing the "Power Save" concept. For very low power applications or for TEC-less (Thermo-Electric-Cooler) applications, the flexible dilution architecture enables the system to operate the detector at a number of formats. This, together with a smooth frame rate and format transition capability turns SCD's uncooled detector to be well suited for unattended applications. These issues will be described in detail as well.
SCD has recently presented an un-cooled detector product line based on the high-end VOx bolometer technology1. The
first PFA launched, BIRD, is a 384x288 (or 320x240) configurable format with 25μm pitch. Typical NETD values for
these FPAs range at 50mK with an F/1 aperture and 60 Hz frame rate. These detectors also exhibit a relatively fast
thermal time constant of approximately 10 msec.
In this paper we elaborate on the special advanced features that were incorporated within the ROIC and supporting
algorithms. In this framework we have addressed two important issues: the power consumption and the time span
between shutter activations. Minimum power consumption is a critical issue for many un-cooled applications. SCD has
addressed this by introducing the "Power-Save" concept accompanied with flexible dilution architecture. The paper will
present recent results exhibiting the various advantages.
One of the limiting factors on the performance of un-cooled detectors is their vulnerability to ambient drift. Usually,
even minor temperature fluctuations are manifested as high residual non-uniformity (RNU) or fixed pattern noise (FPN).
As a result frequent shutter operations must be applied, with the risk of blocking the scenery in critical time frames. The
challenge is thus twofold: increase the time span between shutter corrections and achieve better control of its activation.
For this purpose BIRD provides two complementing mechanisms: A real-time (frame-by-frame) ambient drift compensation accompanied by an RNU prediction mechanism. The paper will discuss these features in detail and present illustrative system implementations.
SCD is unveiling the first member of its new uncooled product line based on the high-end VOx technology. The detector is software configurable to various format standards including 384x288, 320x240 and others with 25μm pitch. The NETD values for these FPAs are better then 50mK with F#/1 aperture and 60 Hz frame rate. These detectors also exhibit a relatively fast thermal time constant of approximately 10msec. In order to improve the system level "cost-performance" in terms of power consumption and weight, SCD has introduced special features within the FPA & package. Among them is a proprietary "Power Save" architecture, in which the die temperature can be stabilized to the ambient temperature or a close enough discrete value, covering the range between -40c and 70c. Thus, the TEC power consumption is considerably reduced with minimal performance degradation. An additional benefit is improved "mission readiness" which is of vital importance for various system applications. A major limitation of systems based on uncooled detectors is the poor resilience to the ambient temperature drift. This drift degrades the spatial non-uniformity. As a result, frequent corrections using an optical shutter are required, specifically during the camera stabilization period. In order to increase the time span between shutter operations, SCD has incorporated various real-time monitoring features within the FPA and supporting algorithms. These features reduce the spatial noise by an order of magnitude.