The water-soluble silicon quantum dots (QDs) of average diameter ~3 nm were prepared in organic solvent by ultrasound-induced solution route. This speedy rout produces the silicon QDs in the size range from 2 nm to 4 nm at room temperature and ambient pressure. The product yield of QDs was estimated to be higher than 60 % based on the initial NaSi weight. The surfaces of QDs were terminated with organic molecules including biocompatible ending groups (hydroxyl, amine and carboxyl) during simple preparation. Covalent attached molecules were characterized by FT-IR spectroscopy. These water-soluble passivation of QDs has just a little effect on the optical properties of original QDs.
Influence of quantum dot growth on the electrical properties of Au/GaAs Schottky diode structures containing self-assembled InAs quantum dots fabricated via atomic layer molecular beam epitaxy is investigated. Current-voltage characteristics and low frequency noise measurements were performed and analyzed. Employing four different structures; containing single quantum dot layer, without quantum dot layer for a reference, thicker capping layer with single quantum dot layer, three quantum dot layers, we find the diode containing single quantum dot layer show largest leakage current and all the dots show 1/f behavior in low frequency noise characteristics. Current dependence of the noise current power spectral density shows that all the dots have linear current dependence at low bias which is explained by the mobility and diffusivity fluctuation. The Hooge parameter was determined to be in the range of 10-7 to 10-8. At high bias, the diodes containing quantum dot layer(s) show IFβ dependence with the value of β larger than 2 (3.9, and 2.7), and the diode without quantum dot layer and thicker capping layer show the value of β smaller than 2 (1.6). The deviation of the values of β from two is explained by the random walk of electrons involving interface states at the metal-semiconductor Schottky barrier interface via barrier height modulation. It seems that the growth of quantum dots induces generation of the interface states with its density increasing towards the conduction band edge. The value of β smaller than 2 means that the interface states density is increasing towards the midgap. Typical value of the interface states density was found to be on the order of 1011 to 1012cm2/Vs.
Intermixing effects of MOCVD (metal organic chemical vapor deposition) grown InGaAs SAQDs (self-assembled quantum dots) covered with SiO2 and SiNx-SiO2 dielectric capping layers were investigated. The intermixing of SAQDs was isothermally performed at 700°C by varying annealing time under the N2-gas ambient. It was confirmed from the PL measurement after the thermal annealing that, the emission energy of SAQDs was blue-shifted by 190 meV, the FWHM (full width at half maximum) was narrowed from 76 meV to 47 meV and the PL intensity was increased. SiNx-SiO2 double capping layer have been found to induce larger PL intensity after the thermal annealing of SAQDs compared to SiO2 single capping layer. The results can be implemented for increasing quantum efficiency and tuning the detection wavelength in quantum dot infrared photodetector (QDIP).
Silicon nanoparticles in the range from 2 nm to 5 nm was prepared from Zintl salt, soldium silicide (NaSi) by sonochemical method. This synthesis permits the reaction completed as fast as in a few hours and the easy alkyl-modification of nanocrystals surface at room temperature and ambient pressure. The average size of nanoparticles measured by the dynamic light scattering analysis was 2.7 nm. The high-resolution transmission electron micrograph cofirmed the material identity of nanoparticles as crystalline silicon. FT-IR spectra are consistent with the surface states of nanocrystals that is chlorine- or butyl-capped. The emission peak center moved to longer wavelength (up to 430 nm) with the reaction time, under a 325 nm excitation. The luminescence of silicon colloids looks bright bluish-white under excitation using a commercial low-intensity UV lamp.
Effects of InxGa1-xAs strain relaxation layers on the optical and structural properties of InAs quantum dots (QDs) were studied systemically. 300 K-photoluminescence (PL) shows that PL peak energy of the QDs is blue-shifted in GaAs/InAs QDs/5 nm-thick In0.1Ga0.9As structure compared to GaAs/InAs QDs/GaAs structure. This is attributed to the intermixing of materials between the QDs and the InGaAs layer below the QDs, whereas capping of a 5 nm-thick In0.1Ga0.9As layer leads to red shift due to strain relaxation effect. As thickness of InxGa1-xAs capping layer (TI) increases, 300 K-PL peaks experience red shift below TI < ~7 nm. Unlikely, TI above 7 nm results in blue shift. Considering average height of the QDs is ~ 7 nm, this is attributed to intermixing of material between the QDs and InGaAs capping layers. The blue shift in x = 0.2 over TI > ~7 nm is relatively smaller compared to that in x = 0.1. It is noteworthy that strain difference between the InAs QDs and the InxGa1-xAs is smaller in x = 0.2 rather than in x = 0.1. Finally, InAs QDs are sandwiched by asymmetric thickness (7.5 nm-thick capping InGaAs, 0, 1.2, and 2.5 nm-thick bottom InGaAs) of In0.2Ga0.8As layers. 300 K-PL spectrum shows that 1.2 nm-thick bottom InGaAs leads to the longest wavelength (1306 nm) among this sample set. This is attributed to reduced barrier height and ignorable accumulated strain effect in thin bottom InGaAs layers. In this report, we justify merit of dots in an asymmetric well structure over conventional dots in a symmetric well structure and strain relaxation structure for the control of PL peak energy.
We, here, present the study on the crystalline behavior of TiO2 in the presence of SiO2 and its optical property at low SiO2 content region from x equals 0 and 0.12 in the (1-x)TiO2-xSiO2 system. From X-ray diffraction, it is observed that just a small addition of SiO2 into TiO2-SiO2 films has made a rutile peak completely vanish. Anatase peaks were decreased in intensity and broadened with the increase in added SiO2 content. Besides, anatase peak was shifted to the large d-spacing and its means that Si ions have incorporated into TiO2. However, the anatase peak shift was saturated above 8 mol%. These facts confirmed that incorporated Si ions inhibited the phase transition between the rutile and the anatase and the crystallization of anatase is also suppressed with SiO2 addition. The anatase band frequency (approximately 140 cm-1) shift to the higher one in Raman spectra and the appearance of the band due to Si-O-Ti vibration in IR spectra indicates clearly that the SiO2 incorporation happens as SiO2 is added in films. The surface topography observed by SEM and AFM shows that the surface becomes smooth and the TiO2 crystallite become smaller with increasing SiO2 content. UV-Visible transmittance spectra showed that all films have good transparency up to about 90% in visible region.
Access to the requested content is limited to institutions that have purchased or subscribe to SPIE eBooks.
You are receiving this notice because your organization may not have SPIE eBooks access.*
*Shibboleth/Open Athens users─please
sign in
to access your institution's subscriptions.
To obtain this item, you may purchase the complete book in print or electronic format on
SPIE.org.
INSTITUTIONAL Select your institution to access the SPIE Digital Library.
PERSONAL Sign in with your SPIE account to access your personal subscriptions or to use specific features such as save to my library, sign up for alerts, save searches, etc.