Mr. Robert P. Crist Profile

Robert P. Crist

Engineering Technician at Lawrence Livermore National Lab

SPIE Involvement:

Author

Publications (2)

Proceedings Article | 26 November 2018 Presentation

Novel AMP surface treatment for improving optical fiber strength and laser gain (Conference Presentation)

Diana VanBlarcom, Derrek Drachenberg, Jay Dawson, Michael Messerly, Marcus Monticelli, Gabriel Davalos, Steve Davis, Nick Schenkel, Matthew Cook, Robert Crist

Proceedings Volume 10805, 108051C (2018) https://doi.org/10.1117/12.2501563

KEYWORDS: Fiber lasers, Laser damage threshold, Glasses, Silica, Etching, Coating, National Ignition Facility, Amplifiers, Fiber coatings, Photonic crystals

Read Abstract +

Contaminants can severely limit the efficiency, laser damage threshold, and strength of photonic crystal fiber-based lasers. Such contamination can occur due to environmental exposure during the pulling or stacking of rods and tubes or improper handling and storage of these glass components. A preform made by the “stack and draw” process is susceptible to incorporating surface contaminants into the bulk laser glass. We have adapted cleaning and handling protocols originally developed for processing large fused silica optics for the National Ignition Facility. The etch cleaning process reported here mimics the “AMP” or “Advanced Mitigation Process” developed for NIF optics that see high fluence 351nm light. In addition, all cleaning, fixturing and assembly processes used to prep a stack for pulling into a fiber are done in a Class 100 cleanroom. Glass rods (1-3mm in diameter and 10” long) are assembled into a Teflon fixture that only contacts the rods at each end. The loaded fixture receives 120kHz ultrasonic cleaning in 10% sodium hydroxide at 45C and 3% Brulin 1696 detergent at 55C. Parts are thoroughly rinsed using ultrasonicated ultrapure water and spray rinses. A 200nm etch in buffered hydrofluoric acid (6:1 BOE diluted 2:1 in DI water) is followed by additional ultasonicated (120kHz-270kHz) ultrapure water and spray rinse. Finally, the components are allowed to fully dry inside the Teflon frame. The rods are cleaned, stacked, and assembled into a fused silica tube. The preform stack is then returned to a non-cleanroom area to be pulled into fiber using standard telecom fiber-based draw tower equipment and without clean air filters around the draw area. Four fibers were made to test independently the damage threshold and the background loss, two Yb core active fibers and two silica core (F clad) fibers. One of each was cleaned with the AMP process, and one of each with a methanol wipe cleaning process. The active fiber was coated with a dual acrylate coating, first with a low-index inner coating to provide a pump cladding, and then with a relatively hard coating to protect the relatively soft primary coating. The active fibers were pumped at 980nm in a double Fresnel cavity configuration and the power increased until the fiber was damaged up to 1kW. The passive fiber background loss was measured using a standard cut-back technique. Replacing the former methanol wipe clean process with this aqueous cleaning process improved the 1060nm damage threshold of a fiber laser by >30x to above the kW level in the laboratory and reduced the background attenuation by >18x. Early indications are that the acid etching also makes the tensile strength of the fiber consistently high. This work was performed under the auspices of the U.S. Department of Energy by Lawrence Livermore National Laboratory under Contract DE-AC52-07NA27344.

Proceedings Article | 26 February 2018 Paper

10W single-mode Nd3+ fiber laser at 1428nm

Victor Khitrov, Jay Dawson, Leily Kiani, Paul Pax, Derrek Drachenberg, Michael Messerly, Robert Crist, Nick Schenkel, Matt Cook

Proceedings Volume 10512, 105121P (2018) https://doi.org/10.1117/12.2284876

KEYWORDS: Fiber lasers, Neodymium, Fiber amplifiers, Waveguides, Silica, Laser development, High power fiber amplifiers, Diodes, Laser sources

Read Abstract +

View contact details

UPDATE YOUR PROFILE

Is this your profile? Update it now.

Sign into your SPIE.org account

Don’t have a profile and want one?

Create an account on SPIE.org

Keywords/Phrases

Search In:

Publication Years