Large-format infrared detectors are at the heart of major ground and space-based astronomical instruments, and the HgCdTe HxRG is the most widely used. The Near Infrared Spectrometer and Photometer (NISP) of the ESA’s Euclid mission launched in July 2023 hosts 16 H2RG detectors in the focal plane. Their performance relies heavily on the effect of image persistence, which results in residual images that can remain in the detector for a long time contaminating any subsequent observations. Deriving a precise model of image persistence is challenging due to the sensitivity of this effect to observation history going back hours or even days. Nevertheless, persistence removal is a critical part of image processing because it limits the accuracy of the derived cosmological parameters. We will present the empirical model of image persistence derived from ground characterization data, adapted to the Euclid observation sequence and compared with the data obtained during the in-orbit calibrations of the satellite.
Euclid, the M2 mission of the ESA’s Cosmic Vision 2015-2025 program, aims to explore the Dark Universe by conducting a survey of approximately 14 000 deg2 and creating a 3D map of the observable Universe of around 1.5 billion galaxies up to redshift z ∼ 2. This mission uses two main cosmological probes: weak gravitational lensing and galaxy clustering, leveraging the high-resolution imaging capabilities of the Visual Imaging (VIS) instrument and the photometric and spectroscopic measurements of the Near Infrared Spectrometer and Photometer (NISP) instrument. This paper details some of the activities performed during the commissioning phase of the NISP instrument, following the launch of Euclid on July 1, 2023. In particular, we focus on the calibration of the NISP detectors’ baseline and on the performance of a parameter provided by the onboard data processing (called NISP Quality Factor, QF) in detecting the variability of the flux of cosmic rays hitting the NISP detectors. The NISP focal plane hosts sixteen Teledyne HAWAII-2RG (H2RG) detectors. The calibration of these detectors includes the baseline optimization, which optimizes the dynamic range and stability of the signal acquisition. Additionally, this paper investigates the impact of Solar proton flux on the NISP QF, particularly during periods of high Solar activity. Applying a selection criterion on the QF (called NISP QF Proxy), the excess counts are used to monitor the amount of charged particles hitting the NISP detectors. A good correlation was found between the Solar proton flux component above 30 MeV and the NISP QF Proxy, revealing that NISP detectors are not subject to the lower energy components, which are absorbed by the shielding provided by the spacecraft.
The NISP (Near Infrared Spectrometer and Photometer) is one of the two Euclid instruments (see ref [1]). It operates in the near-IR spectral region (950-2020nm) as a photometer and spectrometer. The instrument is composed of: - a cold (135K) optomechanical subsystem consisting of a Silicon carbide structure, an optical assembly, a filter wheel mechanism, a grism wheel mechanism, a calibration unit and a thermal control system - a detection system based on a mosaic of 16 H2RG with their front-end readout electronic. - a warm electronic system (290K) composed of a data processing / detector control unit and of an instrument control unit that interfaces with the spacecraft via a 1553 bus for command and control and via Spacewire links for science data This paper presents: - the final architecture of the flight model instrument and subsystems - the performances and the ground calibration measurement done at NISP level and at Euclid Payload Module level at operational cold temperature.
Euclid is a major ESA mission for the study of dark energy planned to launch in 2021. Euclid will probe the expansion history of the Universe using weak lensing and baryonic acoustic oscillations probes. A survey of 15,000 deg2 of the sky with the instrument NISP (Near-Infrared Spectro-Photometer), in the 900 – 2100 nm band, will give both the photometric and spectrometric redshifts of tens of millions of galaxies. The 16 H2RG detectors of the NISP focal plane array are still being characterized at CPPM (Marseille). Already 16 out of 20 flight detectors have been tested and a straightforward analysis done. Performance of the dedicated test benches – in particular control of flux and temperature – as well as an overview of the test flow will be presented. This paper will present methods and some preliminary results on two detectors focusing on the determination of a per pixel conversion gain.
Euclid is an ESA mission to map the geometry of the Dark Universe with a planned launch date in 2021.1 Two
primary cosmological probes, weak gravitational lensing and baryonic acoustic oscillations, are implemented
through a VISible imager (VIS) and a Near-Infrared Spectrometer and Photometer (NISP).2 The ground characterization of the NISP Flight Sensor Chip Systems (SCS) followed by the pixel response calibration aims to
produce all informations to correct and control the accuracy of the signal. This work reports on the ground
characterization of the NISP detector chain. The detector and electrical effects are likely to generate statistical
fluctuations and systematic errors on the final flux measurement. The analysis strategies to maintain the pixel
relative response accuracy within 1% is proposed in this work. The Euclid NISP test ow is presented and
the main concerns of the detector chain calibration, such as non-linearity, charge trapping and de-trapping are
discussed on the basis of the analysis of the flight detectors characterization data.
KEYWORDS: Sensors, Data processing, Space operations, Data acquisition, Signal detection, Electronics, Control systems, Interfaces, Software development
In this paper we describe the application software (ASW) of the instrument control unit (ICU) of NISP, the Near-Infrared Spectro-Photometer of the Euclid mission. This software is based on a real-time operating system (RTEMS) and will interface with all the subunits of NISP, as well as the command and data management unit (CDMU) of the spacecraft for telecommand and housekeeping management.
KEYWORDS: Data storage, Near infrared, Computing systems, Data processing, Sensors, Data archive systems, Data modeling, Control systems, Databases, Data conversion
The NISP instrument on board the Euclid ESA mission will be developed and tested at different levels of integration
using various test equipment which shall be designed and procured through a collaborative and coordinated effort. The
NISP Instrument Workstation (NI-IWS) will be part of the EGSE configuration that will support the NISP AIV/AIT
activities from the NISP Warm Electronics level up to the launch of Euclid. One workstation is required for the NISP
EQM/AVM, and a second one for the NISP FM. Each workstation will follow the respective NISP model after delivery
to ESA for Payload and Satellite AIV/AIT and launch. At these levels the NI-IWS shall be configured as part of the
Payload EGSE, the System EGSE, and the Launch EGSE, respectively. After launch, the NI-IWS will be also re-used in
the Euclid Ground Segment in order to support the Commissioning and Performance Verification (CPV) phase, and for
troubleshooting purposes during the operational phase.
The NI-IWS is mainly aimed at the local storage in a suitable format of the NISP instrument data and metadata, at local
retrieval, processing and display of the stored data for on-line instrument assessment, and at the remote retrieval of the
stored data for off-line analysis on other computers.
We describe the design of the IWS software that will create a suitable interface to the external systems in each of the
various configurations envisaged at the different levels, and provide the capabilities required to monitor and verify the
instrument functionalities and performance throughout all phases of the NISP lifetime.
KEYWORDS: Control systems, Software development, Space operations, Data processing, Sensors, Control systems, Data acquisition, Field programmable gate arrays, Technetium, Electronics, Calibration
In this paper we describe the detailed design of the application software (ASW) of the instrument control unit (ICU) of
NISP, the Near-Infrared Spectro-Photometer of the Euclid mission. This software is based on a real-time operating
system (RTEMS) and will interface with all the subunits of NISP, as well as the command and data management unit
(CDMU) of the spacecraft for telecommand and housekeeping management. We briefly review the main requirements
driving the design and the architecture of the software that is approaching the Critical Design Review level. The
interaction with the data processing unit (DPU), which is the intelligent subunit controlling the detector system, is
described in detail, as well as the concept for the implementation of the failure detection, isolation and recovery (FDIR)
algorithms. The first version of the software is under development on a Breadboard model produced by
AIRBUS/CRISA. We describe the results of the tests and the main performances and budgets.
The Euclid mission objective is to understand why the expansion of the Universe is accelerating through by mapping the geometry of the dark Universe
by investigating the distance-redshift relationship and tracing the evolution of cosmic structures. The Euclid project is part of ESA's Cosmic Vision
program with its launch planned for 2020 (ref [1]).
The NISP (Near Infrared Spectrometer and Photometer) is one of the two Euclid instruments and is operating in the near-IR spectral region (900-
2000nm) as a photometer and spectrometer. The instrument is composed of:
- a cold (135K) optomechanical subsystem consisting of a Silicon carbide structure, an optical assembly (corrector and camera lens), a filter wheel
mechanism, a grism wheel mechanism, a calibration unit and a thermal control system
- a detection subsystem based on a mosaic of 16 HAWAII2RG cooled to 95K with their front-end readout electronic cooled to 140K, integrated on a
mechanical focal plane structure made with molybdenum and aluminum. The detection subsystem is mounted on the optomechanical subsystem
structure
- a warm electronic subsystem (280K) composed of a data processing / detector control unit and of an instrument control unit that interfaces with the
spacecraft via a 1553 bus for command and control and via Spacewire links for science data
This presentation describes the architecture of the instrument at the end of the phase C (Detailed Design Review), the expected performance, the
technological key challenges and preliminary test results obtained for different NISP subsystem breadboards and for the NISP Structural and Thermal
model (STM).
KEYWORDS: Space telescopes, Space operations, Telescopes, Space operations, Local area networks, Databases, Control systems, Fermium, Frequency modulation, Device simulation, Data modeling
The Near Infrared Spectro-Photometer (NISP) on board the Euclid ESA mission will be developed and tested at various
levels of integration by using various test equipment. The Electrical Ground Support Equipment (EGSE) shall be
required to support the assembly, integration, verification and testing (AIV/AIT) and calibration activities at instrument
level before delivery to ESA, and at satellite level, when the NISP instrument is mounted on the spacecraft. In the case of
the Euclid mission this EGSE will be provided by ESA to NISP team, in the HW/SW framework called "CCS Lite", with
a possible first usage already during the Warm Electronics (WE) AIV/AIT activities. In this paper we discuss how we
will customize that "CCS Lite" as required to support both the WE and Instrument test activities. This customization will
primarily involve building the NISP Mission Information Base (the CCS MIB tables) by gathering the relevant data from
the instrument sub-units and validating these inputs through specific tools. Secondarily, it will imply developing a
suitable set of test sequences, by using uTOPE (an extension to the TCL scripting language, included in the CCS
framework), in order to implement the foreseen test procedures. In addition and in parallel, custom interfaces shall be set
up between the CCS and the NI-IWS (the NISP Instrument Workstation, which will be in use at any level starting from
the WE activities), and also between the CCS and the TCC (the Telescope Control and command Computer, to be only
and specifically used during the instrument level tests).
Access to the requested content is limited to institutions that have purchased or subscribe to SPIE eBooks.
You are receiving this notice because your organization may not have SPIE eBooks access.*
*Shibboleth/Open Athens users─please
sign in
to access your institution's subscriptions.
To obtain this item, you may purchase the complete book in print or electronic format on
SPIE.org.
INSTITUTIONAL Select your institution to access the SPIE Digital Library.
PERSONAL Sign in with your SPIE account to access your personal subscriptions or to use specific features such as save to my library, sign up for alerts, save searches, etc.