Fluoropolymers are key materials in the single-layer resists used in 157-nm lithography. We have been studying fluoropolymers to determine their potential use as base resins. These polymers are main-chain fluorinated polymers synthesized by co-polymerizing tetrafluoroethylene (TFE) and functional norbornene. We developed a new polymer that is highly transparent and has high dry-etching resistance by attaching a PG-F protecting group, which has high dry-etching resistance, to a TFE/norbornene-based fluorinated polymer. The dry-etching rate for the 15 % blocked polymer was 1.50 times that of a KrF resist and its absorption coefficient at a 157-nm-exposure wavelength was 1.06 /μm. We introduced various photoacid generators (PAGs) to the polymer, and compared lithographic performance. As a result, we found polymer with a triphenylsulfonium-salts-based PAG had a good pattern profile, and polymer with a high-acidity PAG resolved a fine pattern. In particular, polymer with a triphenylsulfonium perfluorooctane sulfonate PAG was able to resolve a 60-nm line and space pattern. We then added various quenchers to the polymer and the PAG, and compared pattern profiles. We found that the use of a high-basicity quencher improved the resolution of the resist and line edge roughness. Consequently, that the polymer with the triphenylsulfonium perfluorooctane sulfonate PAG and tributylamine quencher could resolve a 55-nm line and space pattern. These results provided guidelines for choosing the PAG and quencher for this polymer.
Main-chain-fluorinated base-resins, using the copolymer of tetrafluoroethylene and functional (hexafluoroisopropanol (HFA) group) norbornene, were synthesized. Partial protection of its hydroxyl group as ethoxymethyl group was achieved by two methods, by copolymerization (Method A) or by polymer reaction (Method B). The partial protection by copolymerization was conducted by copolymerizing TFE with the mixture of protected and unprotected monomers (Method A, copolymerization). The partial protection was also carried out by reacting hydroxyl group of the polymer, which is composed of TFE and unprotected monomers with ethoxymethyl chloride in the presence of an amine (Method B). In the polymer reaction, only exo position of the norbornene unit was protected. Their fundamental properties, such as transparency at 157 nm and solubility in a standard alkaline developer, were characterized and studied. A high transparency, i.e., absorbance of less than 0.4 μm-1, was achieved in both methods. However, the polymer prepared by the polymer reaction (Method B) was deprotected more quickly. And this polymer had a higher dissolution rate and development contrast than the polymer prepared by copolymerization (Method A). The Positive-working resists based on this fluororesins were developed and 55 nm dense lines could be delineated by the exposure at 157 nm wavelength with alternating phase shift mask on a 0.9 NA 157 nm exposure tool.
Fluorinated polymers show a good transparency at the 157-nm exposure wavelength for single-layer resists. We have developed fluorinated resist polymers for 157-nm lithography. These polymers are main-chain fluorinated polymers synthesized by the co-polymerization of tetrafluoroethylene (TFE) and polymers such as poly(TFE/norbornene/α-fluoroolefin) fluoropolymers (FP1). In this paper, a number of polymerization initiators were evaluated in the polymerization of PF1-type polymers in order to investigate the effect of polymer end groups on optical and dissolution properties. We found that the polymer end group greatly affects the dissolution properties of these polymers when using a standard 0.26N tetramethylammonium hydroxide (TMAH) aqueous developer solution. These end groups also affect the polymer transparencies at 157-nm, and the resulting lithographic performance. The fluorocarbon initiator named “F2” induced the lowered absorbance (~0.4μm-1) and an increase in the dissolution rate (~300 nm/sec) without noticeable amounts of swelling. These polymer-based resists can achieve a resolution of less than 60-nm using a 157-nm laser microstepper (NA=0.85) with a Levenson-type strong phase shifting mask.
We have synthesized various main-chain fluorinated polymers and studied their transparency and solubility. The main-chain fluorinated polymers were synthesized by co- or ter-polmerization of tetrafluoeoethylene (TFE) with cyclic monomers, especially TFE with newly synthesized norbornene derivatives. Transparency of the main-chain fluorinated polymers tended to be higher with higher fluorine contents. But exact absorbance of the main-chain fluorinated polymers by modifying the STUPID calculation. Solubility of the main-chain fluorinated polymers functionalized by hydroxyfluoroalkyl groups was also studied. We have developed a model to predict pKa of hydroxyfluoroalkyl groups incorporated in the norbornene derivatives, and studied correlation between pKa(OH) and solubility of the co-polymers of the hydroxyfluoroalkyl-functionalized norbornene derivatives with TFE. pKa
Of the hydroxyfluoroalkyl groups were lower with higher fluorine contents, and solubility of the co-polymers tended to be higher with lower pKa of the hydroxyalkyl groups.
Main-chain-fluorinated base-resins, including tetrafluoroethylene and norbornene derivatives, were synthesized and their fundamental properties, such as transparency at 157 nm and solubility in a standard alkaline developer, were characterized. A high transparency, i.e., absorbance of less then 0.5 μm-1, was achieved by optimizing the polymerization conditions with a variety of counter monomers. It was found that the polymerization conditions could also control the dissolution rates of the fluoropolymers and increased the dissolution rate of unprotected fluoropolymers by about three orders of magnitude, which was sufficient for the alkaline developability. Positive-working resists based on fluororesins were developed and showed good transparency of less than 1 μm-1 at 157 nm, and good solubility in a standard alkaline solution of 0.26-N tetramethylammonium (without any swelling behavior). And an acceptable etching rate as resistant as ArF resists was obtained and 65-nm dense lines could be delineated by the exposure at 157-nm wavelength.
The reactive ion etch (RIE) properties of fluorine funtionalized polymers in which fluorine atoms were incorporated in the main chain were examined. There was a tendency that the etching rates of these polymers were higher as lower the fluorine contents. The existing four models such as the Ohnishi model, the Kunz model, the Ohfuji model and the Kishimura model were applied to explain the correlation between the etching rates and the polymer compositions or structures, but the errors were too large to explain the relationship. A new model has developed to explain the effect of the fluorine incorporation to the dry etch resistance. The model assumed that there would be a correlation between the number of main chain fluorine atoms and the dry etch resistance, and the main chain fluorine incorporation would increase the dry etch resistance. The model could explain the dry etch resistance of the main chain fluorine incorporated polymers with adequate accuracy.
Access to the requested content is limited to institutions that have purchased or subscribe to SPIE eBooks.
You are receiving this notice because your organization may not have SPIE eBooks access.*
*Shibboleth/Open Athens users─please
sign in
to access your institution's subscriptions.
To obtain this item, you may purchase the complete book in print or electronic format on
SPIE.org.
INSTITUTIONAL Select your institution to access the SPIE Digital Library.
PERSONAL Sign in with your SPIE account to access your personal subscriptions or to use specific features such as save to my library, sign up for alerts, save searches, etc.