This PDF file contains the front matter associated with SPIE Proceedings Volume 9912, including the Title Page, Copyright information, Table of Contents, Introduction (if any), and Conference Committee listing.

NFIRAOS is the first light adaptive optics system for the Thirty Meter Telescope (TMT). NFIRAOS components are maintained at a stable -30°C ±0.5°C by embedding an actively cooled refrigeration system in the walls of the NFIRAOS enclosure. Three instruments are attached to interface ports in the NFIRAOS enclosure and are required to be thermally stable while the instrument rotates in place. Additionally, instruments must be installed and removed while NFIRAOS is cold to avoid lengthy cool-down cycles. A portion of the actively cooled enclosure system and the interface has been prototyped at NRC-Herzberg. We present a description of the design of the interface and results of testing so far and lessons learned.

The differential Optical Transfer Function (dOTF) is a focal plane wavefront sensing method that uses a diversity in the pupil plane to generate two different focal plane images. The difference of their Fourier transforms recovers the complex amplitude of the pupil down to the spatial scale of the diversity. We produce two simultaneous PSF images with diversity using a polarizing filter at the edge of the telescope pupil, and a polarization camera to simultaneously record the two images. Here we present the first on-sky demonstration of polarization dOTF at the 1.0m South African Astronomical Observatory telescope in Sutherland, and our attempt to validate it with simultaneous Shack-Hartmann wavefront sensor images.

Over the last decade TNO has developed a deformable mirror concept using electromagnetic actuators with the main advantages of having very low non-linearity and hysteresis, low power consumption, and high inherent reliability of the actuators. TNO recently started a program to redesign the electromagnetic actuator to improve the actuator efficiency, allowing higher actuator force per volume and per wattage. The increased actuator efficiency gives improvement of the DM performance in terms of dynamical performance, actuation range, and power dissipation. With this technology various applications in the fields of ground-based astronomy and space missions are targeted.

The early-light facility adaptive optics system for the Thirty Meter Telescope (TMT) is the Narrow-Field InfraRed Adaptive Optics System (NFIRAOS). The science beam splitter changer mechanism and the visible light beam splitter are subsystems of NFIRAOS. This paper presents the opto-mechanical design of the NFIRAOS beam splitters subsystems (NBS). In addition to the modal and the structural analyses, the beam splitters surface deformations are computed considering the environmental constraints during operation. Surface deformations are fit to Zernike polynomials using SigFit software. Rigid body motion as well as residual RMS and peak-to-valley surface deformations are calculated. Finally, deformed surfaces are exported to Zemax to evaluate the transmitted and reflected wave front error. The simulation results of this integrated opto-mechanical analysis have shown compliance with all optical requirements.

The Ball Fiber Optical Comb Demo is a lab-based system which is used to develop space applications for optical frequency combs. These developments utilize the broadband optical coherence of the frequency comb to expand the capabilities of ground test and orbital systems used for optical wave-front measurement, control of adaptive optics, precision ranging, and reference frequency stabilization. The work expands upon a NIST-developed all-fiber frequency comb that exhibits high stability in a compact, enclosed package.

Previously demonstrated applications for frequency combs include: Spectroscopy, distance and velocity measurement, frequency conversion, and timing transfer. Results from the Ball system show the characterization and performance of a frequency comb system with a technological path-to-space. Demonstrations in high precision metrology and long distance ranging are also presented for application in adaptive and multi-body optical systems.

The Segmented Mirror Telescopes (SMT) are built using small hexagonal mirror segments placed side by side to form a monolithic primary mirror of very large size. The effective figure of such a segmented primary mirror is maintained against external disturbances introduced by gravity, temperature, wind and vibration with the help of primary mirror active control system. This active control system consists of two levels of control – global and local level. At the global scale, three actuators per segment and two edge sensors per intersegment sides are used to maintain the shape of the primary mirror. At the local level, actuator control system executes the commands generated by the global control loop. Every mirror segment is controlled with the help of three actuators, where the major role of these actuators is to provide a tip, tilt, and piston to the mirror segments. In this paper, we describe the actuator developed for 1.5m diameter Prototype Segmented Mirror Telescope (PSMT). The actuator for this telescope is a soft actuator based on the voice coil mechanism. This actuator is designed for with the range of travel of ±1.5mm and the force range of 25N along with an offloading capability to reduce the power consumption. The prototype actuator is undergoing different tests at Indian Institute of Astrophysics (IIA), Bangalore. The tracking rate of 324nm/s is achieved with the tracking error of 22.5 nm RMS.

The decisive influence on breakage strength of brittle materials such as the low expansion glass ceramic ZERODUR is the surface condition. For polished or etched surfaces it is essential if micro cracks are present and how deep they are. Ground surfaces have many micro cracks caused by the generation process. Here only the depths of the micro cracks are relevant. In any case presence and depths of micro cracks are statistical by nature.

The Weibull distribution is the model used traditionally for the representation of such data sets. It is based on the weakest link ansatz. The use of the two or three parameter Weibull distribution for data representation and reliability prediction depends on the underlying crack generation mechanisms. Before choosing the model for a specific evaluation, some checks should be done. Is there only one mechanism present or is it to be expected that an additional mechanism might contribute deviating results? For ground surfaces the main mechanism is the diamond grains’ action on the surface. However, grains breaking from their bonding might be moved by the tool across the surface introducing a slightly deeper crack. It is not to be expected that these scratches follow the same statistical distribution as the grinding process. Hence, their description with the same distribution parameters is not adequate. Before including them a dedicated discussion should be performed.

If there is additional information available influencing the selection of the model, for example the existence of a maximum crack depth, this should be taken into account also. Micro cracks introduced by small diamond grains on tools working with limited forces cannot be arbitrarily deep. For data obtained with such surfaces the existence of a threshold breakage stress should be part of the hypothesis. This leads to the use of the three parameter Weibull distribution. A differentiation based on the data set alone without preexisting information is possible but requires a large data set. With only 20 specimens per sample such differentiation is not possible. This requires 100 specimens per set, the more the better.

The validity of the statistical evaluation methods is discussed with several examples. These considerations are of special importance because of their consequences on the prognosis methods and results. Especially the use of the two parameter Weibull distribution for high strength surfaces has led to non-realistic results. Extrapolation down to low acceptable probability of failure covers a wide range without data points existing and is mainly influenced by the slope determined by the high strength specimens. In the past this misconception has prevented the use of brittle materials for stress loads, which they could have endured easily.

FAME (Freeform Active Mirror Experiment - part of the FP7 OPTICON/FP7 development programme) intends to demonstrate the huge potential of active mirrors and freeform optical surfaces. Freeform active surfaces can help to address the new challenges of next generation astronomical instruments, which are bigger, more complex and have tighter specifications than their predecessors.

The FAME design consists of a pre-formed, deformable thin mirror sheet with an active support system. The thin face sheet provides a close to final surface shape with very high surface quality. The active array provides the support, and through actuation, the control to achieve final surface shape accuracy.

In this paper the development path, trade-offs and demonstrator design of the FAME active array is presented. The key step in the development process of the active array is the design of the mechanical structure and especially the optimization of the actuation node positions, where the actuator force is transmitted to the thin mirror sheet. This is crucial for the final performance of the mirror where the aim is to achieve an accurate surface shape, with low residual (high order) errors using the minimum number of actuators. These activities are based on the coupling of optical and mechanical engineering, using analytical and numerical methods, which results in an active array with optimized node positions and surface shape.

A new type Stressed Mirror Polishing method using annular polishing machine is developed in NIAOT. It provides good efficiency for the massive production of off-axis segments for the extremely large telescope because 3 or more pieces of segment can be polished simultaneously on a AP machine. With an annular polishing machine with 3.6m diameter, two scale-down TMT segments have been polished. Both 2 segments are Φ1100mm in diameter, with the vertex radius of curvature of 60m and aspheric constant K=-1.000953. The off-axis distances (OAD) are 8m and 12m respectively. After SMAP process, the acceptable surface accuracy can be reached, which is 1.12μm/0.23μm of PV/RMS value for the segment with 8m OAD, and 1.22 μm/0.26 μm for another one.

The research works are summarized for Φ1.1m off-axis aspheric segments which are scaled-down TMT segments polished by NIAOT using SMAP (Stressed Mirror Annular Polishing) method in the previous phase and testing preparations for 1.45m mirrors. The detailed introduction is given on result of errors analysis in contact detection testing of segments. In the second part, the selected basis of sampling number for contact-type detector arrays and the terms number of Zernike polynomials we need are studied. And the situations on orthogonality destruction of Zernike polynomials in discrete points sampling case and spectral analysis for each order Spherical aberrations in continuous sampling are introduced.

The Rapid Infrared Imager/Spectrograph (RIMAS) is an instrument designed to observe gamma ray burst afterglows following initial detection by the SWIFT satellite. Operating in the near infrared between 0.9 and 2.4 μm, it has capabilities for both low resolution (R~25) and moderate resolution (R~4000) spectroscopy. Two zinc selenide (ZnSe) grisms provide dispersion in the moderate resolution mode: one covers the Y and J bands and the other covers the H and K. Each has a clear aperture of 44 mm. The YJ grism has a blaze angle of 49.9° with a 40 μm groove spacing. The HK grism is blazed at 43.1° with a 50 μm grooves spacing.

Previous fabrication of ZnSe grisms on the Precision Engineering Research Lathe (PERL II) at LLNL has demonstrated the importance of surface preparation, tool and fixture design, tight thermal control, and backup power sources for the machine. The biggest challenges in machining the RIMAS grisms are the large grooved area, which indicates long machining time, and the relatively steep blaze angle, which means that the grism wavefront error is much more sensitive to lathe metrology errors. Mitigating techniques are described.

MEGARA (Multi-Espectrógrafo en GTC de Alta Resolución para Astronomía) is the new integral-field and multi-object optical spectrograph for the 10.4m Gran Telescopio Canarias.. It will offer R_FWHM ~6,000, 12,000 and 18,700 for the low- , mid- and high-resolution, respectively in the wavelength range 3650-9700Å. .The dispersive elements are volume phase holographic (VPH) gratings, sandwiched between two flat Fused Silica windows of high optical precision in large apertures. The design, based in VPHs in combination with Ohara PBM2Y prisms allows to keep the collimator and camera angle fixed. Seventy three optical elements are being built in Mexico at INAOE and CIO. For the low resolution modes, the VPHs windows specifications in irregularity is 1 fringe in 210mm x 170mm and 0.5 fringe in 190mm x 160mm. for a window thickness of 25 mm. For the medium and high resolution modes the irregularity specification is 2 fringes in 220mm x 180mm and 1 fringe in 205mm x 160mm, for a window thickness of 20mm. In this work we present a description of the polishing techniques developed at INAOE optical workshop to fabricate the 36 Fused Silica windows and 24 PBM2Y prisms that allows us to achieve such demanding specifications. We include the processes of mounting, cutting, blocking, polishing and testing.

An ion beam figuring system (KDIBF2000) for final figuring of large size optics has been designed and built by National University of Defense Technology in China. It can figure optics up to the maximum dimensions of 2.0m×2.0m×0.4m with five axes of servo-motion used to control ion source movement. For operational facility, there are two vacuum chambers with main work chamber and a small supplementary chamber isolated by a flapper valve. The main chamber has two work zones, which can meantime hold a large optics with Φ1.5m and a small optics with 0.4m. The small optics can be transferred through supplementary chamber with a moving vehicle. By this way, it is very convenient and economical to gain the material removal function and check the system’s process performance. Now, this system has been gone into running to figure large SiC off-axis aspheric optics. Next step, a 1.2m SiC aspheric primary mirror will be figure by this system.

Several next generation astronomical telescopes or large optical systems utilize aspheric/freeform optics for creating a segmented optical system. Multiple mirrors can be combined to form a larger optical surface or used as a single surface to avoid obscurations. In this paper, we demonstrate a specific case of the Daniel K. Inouye Solar Telescope (DKIST). This optic is a 4.2 m in diameter off-axis primary mirror using ZERODUR thin substrate, and has been successfully completed in the Optical Engineering and Fabrication Facility (OEFF) at the University of Arizona, in 2016. As the telescope looks at the brightest object in the sky, our own Sun, the primary mirror surface quality meets extreme specifications covering a wide range of spatial frequency errors. In manufacturing the DKIST mirror, metrology systems have been studied, developed and applied to measure low-to-mid-to-high spatial frequency surface shape information in the 4.2 m super-polished optical surface. In this paper, measurements from these systems are converted to Power Spectral Density (PSD) plots and combined in the spatial frequency domain. Results cover 5 orders of magnitude in spatial frequencies and meet or exceed specifications for this large aspheric mirror. Precision manufacturing of the super-polished DKIST mirror enables a new level of solar science.

In this paper we share some recent work performed at REOSC in the domain of advanced optics for space and that is also directly applicable to astronomical instrumentation, e.g. for the Extremely Large Telescopes (ELT), the construction of which has already started. We present firstly the results of some design investigations performed on Three Mirror Anastigmat (TMA) imaging optics when using freeform optical surfaces clearly showing gain in performance (WFE, distortion, … ) or compactness of the optics. We separate smart freeform from more aggressive freeform offering increased level of gain in design performances.

Secondly we present our development in freeform and direct off-axis high performance optical manufacturing capabilities and the industrialization efforts conducted in the frame of the European Extremely Large Telescope (E-ELT) primary mirror segments.

A third subject is the demonstration of an extreme freeform surface manufacturing with the prototyping of a huge 500 mm aperture, 90° deviation angle, F/2.5 high output NA Off Axis Parabola (OAP), a unique achievement aimed to confirm the viability of potential new design opportunities involving such type of extreme optics.

Finally we present in this paper our technology development on polishing layer for SiC material, named R-SiC, a polishing layer that reduces costs, risks and schedule for advanced SiC optics manufacturing for Vis and IR applications.

Large amounts of low thermal expansion material are required for the upcoming ELT projects. The main mirror is designed using several hundreds of hexagonal 1.4 m sized mirror blanks. The M2 and M3 are monolithic 4 m class mirror blanks. The mirror blank material needs to fulfill tight requirements regarding CTE specification and homogeneity.

Additionally the mirror blanks need to be dimensionally stable for more than 30 years. In particular, stress effects due to the changes in the environment shall not entail shape variation of more than 0.5 μm PV within 30 years.

In 2010 SCHOTT developed a physically based model to describe the thermal and mechanical long time behavior of ZERODUR. The model enables simulation of the long time behavior of ZERODUR mirror blanks under realistic mechanical and thermal constraints. This presentation shows FEM simulation results on the long time behavior of the ELT M1, M2 and M3 mirror blanks under different loading conditions. Additionally the model results will be compared to an already 15 years lasting long time measurement of a ZERODUR sample at the German federal physical standardization institute (PTB).

In recent years SCHOTT pushed the push rod dilatometer measurement technology to its limit. With the new Advanced Dilatometer CTE measurement accuracies of +- 3 ppb/K and reproducibilities of better 1 ppb/K have been achieved. The new Advanced Dilatometer exhibits excellent long time stability.

Space bound as well as earthbound spectroscopy of extra-terrestrial objects finds its challenge in light sources with low intensities. High transmission for every optical element along the light path requires optical materials with outstanding performance to enable the measurement of even a one-photon event. Using the Lunar Laser Ranging Project and the LIGO and VIRGO Gravitational Wave Detectors as examples, the influence of the optical properties of fused silica will be described. The Visible and Infrared Surveillance Telescope for Astronomy (VISTA) points out the material behavior in the NIR regime, where the chemical composition of optical materials changes the performance. Special fibers are often used in combination with optical elements as light guides to the spectroscopic application. In an extended spectral range between 350 and 2,200 nm Heraeus developed STU fiber preforms dedicated for broad band spectroscopy in astronomy. STU fibers in the broad spectral range as well as SSU fibers for UV transmission (180 – 400 nm) show also high gamma radiation resistance which allows space applications.

NEXCERA^TM cordierite ceramics, which have ultra-low thermal expansion properties, are perfect candidate materials to be used for light-weight satellite mirrors that are used for geostationary earth observation and for mirrors used in ground-based astronomical metrology. To manufacture the high precision aspheric shapes required, the deterministic aspherization and figure correction capabilities of Magnetorheological Finishing (MRF) are tested. First, a material compatibility test is performed to determine the best method for achieving the lowest surface roughness of RMS ~0.8nm on plano surfaces made of NEXCERA^TM ceramics. Secondly, we will use MRF to perform high precision figure correction and to induce a hyperbolic shape into a conventionally polished 100mm diameter sphere.

In the scope of EUCLID spatial mission, NISP instrument requires high positioning accuracy and high dimensional stability to achieve the required optical performances. LAM is in charge of the development of the instrument main structure which is based on silicon carbide material technology and allows the accurate positioning and maintain of the optomechanical concept sub-systems. This article presents the main steps of this development. It describes the challenging design of this mechanical concept. The associated finite element model, demonstrating the thermomechanical strength of the structure, is presented. Spatial environment vibrations tests performed on the hardware are explained and detailed: requirements, instrumentation and test methodology with the introduction of notching. Finally, the correlation study between finite element analyses and tests is exposed.

Daniel K. Inouye Solar Telescope (formerly known as Advanced Technology Solar Telescope) will be the largest optical solar telescope ever built to provide greatly improved image, spatial and spectral resolution and to collect sufficient light flux of Sun. To meet the requirements of the telescope the design adopted a 4m aperture off-axis parabolic primary mirror with challenging specifications of the surface quality including the surface figure, irregularity and BRDF. The mirror has been completed at the College of Optical Sciences in the University of Arizona and it meets every aspect of requirement with margin. In fact this mirror may be the smoothest large mirror ever made.

This paper presents the detail fabrication process and metrology applied to the mirror from the grinding to finish, that include extremely stable hydraulic support, IR and Visible deflectometry, Interferometry and Computer Controlled fabrication process developed at the University of Arizona.

The Giant Magellan Telescope (GMT) primary mirror consists of seven 8.4 m light-weight honeycomb mirrors that are being manufactured at the Richard F. Caris Mirror Lab (RFCML), University of Arizona. In order to manufacture the largest and most aspheric astronomical mirrors various high precision fabrication technologies have been developed, researched and implemented at the RFCML. The unique 8.4 m (in mirror diameter) capacity fabrication facilities are fully equipped with large optical generator (LOG), large polishing machine (LPM), stressed lap, rigid conformal lap (RC lap) and their process simulation/optimization intelligence called MATRIX. While the core capability and key manufacturing technologies have been well demonstrated by completing the first GMT off-axis segment, there have been significant hardware and software level improvements in order to improve and enhance the GMT primary mirror manufacturing efficiency. The new and improved manufacturing technology plays a key role to realize GMT, the next generation extremely large telescope enabling new science and discoveries, with high fabrication efficiency and confidence.

Polishing and testing methods used in the manufacture of the 3.4 m primary mirror of the Iranian National Observatory (INO) telescope are described and the test results of the finished mirror are presented. Mirror lapping and polishing was performed using several rectangular non-rotating tools arranged in a linear array across the mirror radius. Each tool is equipped with two computer controlled force actuators for regulating the surface pressure and removal efficiency during the lapping and polishing operations. The same tool system was used from the lapping phase to the end of the final polishing. The principal optical test method was the interferometric Hartmann test with the aid of a two component null lens in the mirror center of curvature. Mirror measurements were made also with pentaprism test to verify its correct conic constant. The mirror was finished to extremely good surface accuracy and smoothness.

Modern large telescopes such as TAO, LSST, TMT and EELT require 0.9m-4m monolithic convex secondary mirrors. The fabrication and testing of these large convex secondary mirrors of astronomical telescopes is getting challenging as the aperture of the mirror is getting bigger. The biggest challenge to fabricate these large convex aspheric mirrors is to measure the surface figure to a few nanometers, while maintaining the testing and fabrication cycle to be efficient to minimize the downtime. For the last a couple of decades there was huge advancement in the metrology and fabrication of large aspheric secondary mirrors. College of Optical Sciences in the University Arizona developed a full fabrication and metrology process with extremely high accuracy and efficiency for manufacturing the large convex secondary mirrors.

In this paper modern metrology systems including Swing-Arm Optical Coordinate Measuring System (SOCMM) which is comparable to Interferometry and a Sub-aperture stitching interferometry scalable to a several meters have been presented. Also a Computer Controlled Fabrication Process which produces extremely fine surface figure and finish has been demonstrated. These most recent development has been applied to the fabrication and testing of 0.9m aspheric convex secondary mirror for the Tokyo Atacama Observatory’s 6.5m telescope and the result has been presented.

The Advanced Mirror Technology Development (AMTD) project is in Phase 2 of a multiyear effort initiated in Fiscal Year (FY) 2012, to mature toward the next Technology Readiness Level (TRL) critical technologies required to enable 4-m-or-larger monolithic or segmented ultraviolet, optical, and infrared (UVOIR) space telescope primary-mirror assemblies for general astrophysics and ultra-high-contrast observations of exoplanets. Key hardware accomplishments of 2015/16 are the successful low-temperature fusion of a 1.5-meter diameter ULE mirror that is a 1/3rd scale model of a 4-meter mirror and the initiation of polishing of a 1.2-meter Extreme-Lightweight Zerodur mirror. Critical to AMTD’s success is an integrated team of scientists, systems engineers, and technologists; and a science-driven systems engineering approach.

Reosc has been working on thin glass shells for many years and was recently selected by ESO for the production of the E-ELT M4 mirror thin glass shells. Previously Reosc also produced the aspheric thin shell for the VLT-M2 AO Facility. Based on this experience we will discuss how off axis thin glass shells can be made for the next generation AO systems like the GMT one.

The Richard F. Caris Mirror Lab at the University of Arizona is responsible for production of the eight 8.4 m segments for the primary mirror of the Giant Magellan Telescope, including one spare off-axis segment. We report on the successful casting of Segment 4, the center segment. Prior to generating the optical surface of Segment 2, we carried out a major upgrade of our 8.4 m Large Optical Generator. The upgrade includes new hardware and software to improve accuracy, safety, reliability and ease of use. We are currently carrying out an upgrade of our 8.4 m polishing machine that includes improved orbital polishing capabilities. We added and modified several components of the optical tests during the manufacture of Segment 1, and we have continued to improve the systems in preparation for Segments 2-8. We completed two projects that were prior commitments before GMT Segment 2: casting and polishing the combined primary and tertiary mirrors for the LSST, and casting and generating a 6.5 m mirror for the Tokyo Atacama Observatory.

The LSST M1/M3 combines an 8.4 m primary mirror and a 5.1 m tertiary mirror on one glass substrate. The combined mirror was completed at the Richard F. Caris Mirror Lab at the University of Arizona in October 2014. Interferometric measurements show that both mirrors have surface accuracy better than 20 nm rms over their clear apertures, in nearsimultaneous tests, and that both mirrors meet their stringent structure function specifications. Acceptance tests showed that the radii of curvature, conic constants, and alignment of the 2 optical axes are within the specified tolerances. The mirror figures are obtained by combining the lab measurements with a model of the telescope’s active optics system that uses the 156 support actuators to bend the glass substrate. This correction affects both mirror surfaces simultaneously. We showed that both mirrors have excellent figures and meet their specifications with a single bending of the substrate and correction forces that are well within the allowed magnitude. The interferometers do not resolve some small surface features with high slope errors. We used a new instrument based on deflectometry to measure many of these features with sub-millimeter spatial resolution, and nanometer accuracy for small features, over 12.5 cm apertures. Mirror Lab and LSST staff created synthetic models of both mirrors by combining the interferometric maps and the small highresolution maps, and used these to show the impact of the small features on images is acceptably small.

The development of smart alignment and integration strategies for imaging mirror systems to be used within astronomical instrumentation are especially important with regard to the increasing impact of non-rotationally symmetric optics. In the present work, well-known assembly approaches preferentially applied in the course of infrared instrumentation are transferred to visible applications and are verified during the integration of an anamorphic imaging telescope breadboard. The four mirror imaging system is based on a modular concept using mechanically fixed arrangements of each two freeform surfaces, generated by servo assisted diamond machining and corrected using Magnetorheological Finishing as a figuring and smoothing step. Surface testing include optical CGH interferometry as well as tactile profilometry and is conducted with respect to diamond milled fiducials at the mirror bodies. A strict compliance of surface referencing during all significant fabrication steps allow for an easy integration and direct measurement of the system's wave aberration after initial assembly. The achievable imaging performance, as well as influences of the tight tolerance budget and mid-spatial frequency errors, are discussed and experimentally evaluated.

The new ground based telescope generation is moving to a next stage of performance and resolution. Mirror substrate material properties tolerance and homogeneity are getting into focus. The coefficient of thermal expansion (CTE) homogeneity is even more important than the absolute CTE. The error in shape of a mirror, even one of ZERODUR, is affected by changes in temperature, and by gradients in temperature. Front to back gradients will change the radius of curvature R that in turn will change the focus. Some systems rely on passive athermalization and do not have means to focus. Similarly changes in soak temperature will result in surface changes to the extent there is a non-zero coefficient of thermal expansion. When there are in-homogeneities in CTE, the mirror will react accordingly. Results of numerical experiments are presented discussing the impact of CTE in-homogeneities on the optical performance of 4 m class mirror substrates. Latest improvements in 4 m class ZERODUR CTE homogeneity and the thermal expansion metrology are presented as well.

In this work we discuss some options for using Unmanned Aerial Vehicles (UAVs) for daylight alignment activities and maintenance of optical telescopes, relating them to a small numbers of parameters, and tracing which could be the schemes, requirements and benefits for employing them both at the stage of erection and maintenance. UAVs can easily reach the auto-collimation points of optical components of the next class of Extremely Large Telescopes. They can be equipped with tools for the measurement of the co-phasing, scattering, and reflectivity of segmented mirrors or environmental parameters like C²_n and C²_T to characterize the seeing during both the day and the night.

The Large Millimeter Telescope (LMT) is a single-dish fully-steerable radio telescope presently operating with a 32.5 m parabolic primary reflector, in the process of extension to 50 m. The project is managed by the Instituto Nacional de Astrofísica, Óptica y Electrónica (INAOE) in México, and the University of Massachusetts Amherst, USA. A laminated surface panel from the LMT primary reflector has been subjected to a surface measurement assay at Mexico’s National Metrology Center (CENAM). Data obtained using a coordinate measuring machine and laser tracker owned by CENAM is compared with measurements using an identical model laser tracker and the photogrammetry technique, the latter systems owned and operated by the LMT. All measurements were performed within the controlled metrology environment at CENAM. The measurement exercise is intended to prepare the groundwork for converting this spare surface panel into a calibrated work-piece. The establishment of a calibrated work-piece provides quality assurance for metrology through measurement traceability. It also simplifies the evaluation of measurement uncertainty for coordinate metrology procedures used by the LMT project during reflector surface qualification.

Interference method of testing the long-focus focusing lenses allows measuring such optical parameters as focal distances and distortions of wavefront passing through the lens. High measurement accuracy is achieved by means of a special laser measurement system (laser tracker) in autocollimation schematic based on dynamic interferometer. Main sources of instrument error were found out and their relation to the measurement schematic parameters was defined. The article shows that the method allows achieving total instrument measurement error of the 0.003% of the value being measured.

A deflectometrical facility was developed at Italian National Institute for Astrophysics-OAB to characterize free-form optics with shape errors within few microns rms.

Deflectometry is an interesting technique because it allows the fast characterization of free-form optics. The capabilities of deflectometry in measuring medium-high frequencies are well known, but the low frequencies error characterization is more challenging. Our facility design foresees an innovative approach based on the acquisition of multiple direct images to enhance the performance on the challenging low frequencies range.

This contribution presents the error-budget analysis of the measuring method and a study of the configuration tolerances required to allow the use of deflectometry in the realization of optical components suitable for astronomical projects with a requirement of high accuracy for the optics. As test examples we took into account mirrors for the E-ELT telescope.

With the final installation of the two outermost rings of the primary surface of the Large Millimeter Telescope/ Gran Telescopio Milimétrico (LMT/GTM), the project is also upgrading the primary surface actuators. There are commercial actuators that can approach the required operational accuracy and stroke, but the combination of the size and load requirements ultimately required a customized design. The new actuators fit within the volume constraints imposed by the tighter interior angles in the outer rings and are designed to support the operational and survival loading conditions even for the largest surface segments. Laboratory testing confirmed that the actuators should meet the precision, repeatability, load, and lifetime requirements.

However, the LMT/GTM is at a particularly difficult site for electromechanical systems. The high altitude has the usual effect of reducing cooling effectiveness for the drives and motors, and the ambient temperature hovers near freezing. Since there is a significant amount of precipitation during some times of the year, there are frequent freeze/thaw cycles. The constant formation and either sublimation or melting of ice, along with the associated high humidity, has been a challenge for the environmental protection of many devices at the LMT/GTM. Because there are a total of 720 primary surface actuators in the system, it is particularly important that the actuators, their local drive control boxes, and their cable connections be able to meet its specifications even under the site conditions.

To confirm the suitability of the actuators, the LMT/GTM procured an initial set of sixteen actuators for testing at the site. After laboratory testing, the actuators were installed into the outer two rings of the telescope and cycled during the early winter months of the 2015–16 scientific observing season. Because of the continuing installation activities in these two rings, they are not illuminated by the receivers, so field testing under actual operational conditions could be conducted without affecting the ongoing scientific observations. This paper presents the characterized performance of the actuators before and after testing, as well as a report on their environmental robustness.

Immersed gratings offer several advantages over conventional gratings: more compact spectrograph designs, and by using standard semiconductor industry techniques, higher diffraction-efficiency and lower stray-light can be achieved. We present the optical tests of the silicon immersed grating demonstrator for the Mid-infrared E-ELT Imager and Spectrograph, METIS. We detail the interferometric tests that were done to measure the wavefront-error and present the results of the throughput and stray-light measurements. We also elaborate on the challenges encountered and lessons learnt during the immersed grating demonstrator test campaign that helped us to improve the fabrication processes of the grating patterning on the wafer.

The Near Infrared Spectrometer and Photometer (NISP) of the EUCLID satellite project encompasses high precision large lens mounts of 168 mm diameter that are operated at cryogenic temperatures down to 135K. The four lenses of the optical system are made of different materials: SUPRASIL 30001, CaF2, and S-FTM16, which are mounted in a separate lens mount design using glue connections. Each lens assembly has its individual mechanical interface to the structure, the so called lens barrel. Exhaustive structural and thermal investigations have determined lens surface deformations and lens position changes that are introduced by various environmental loads, such as thermal-, mechanical-, interface-, and gravity loads, as well as mechanical stress of the lenses due to glue shrinkage during curing. All these impacts change the lens optical behaviours under real operational conditions of the optical assembly, which are thoroughly investigated in the optical performance assessment activity. Especially, great effort has been made for the simulation of interface tolerances. Due to the complexity of all mechanical interfaces (baffle, lens mounts, housing, telescope structure, etc.) statistical simulation is conducted applying Monte Carlo method. From the result of the statistical simulation 3 representative cases are selected for the optical performance assessment, which have 95% confidence level of the lens surface deformation. In the context of the evaluation procedure the surface form error of all EUCLID lenses as well as the RMS WFE at the focal plane is assessed, and results are compared with the nominal performance of the system, as well as with interferometrically measured results achieved during the interface– and gravity release test campaign. The performance of the lens holder design in terms of glue shrinkage effects, gravity release and interface tolerances is verified by an adapted test facility including an interferometer based optical metrology system. Finally, the measured values are compared with the analytical results, which show great confidence and hence proves validation of the analytical model. The paper presents the optical performance analysis results and the measured performance of the EUCLID high precision large cryogenic lens mounts. The achievements are presented on behalf of the EUCLID consortium.

To achieve the high adaptive optics sky coverage necessary to allow the GMT Integral-Field Spectrograph (GMTIFS) to access key scientific targets, the on-instrument adaptive-optics wavefront-sensing (OIWFS) system must patrol the full 180 arcsecond diameter guide field passed to the instrument. The OIWFS uses a diffraction limited guide star as the fundamental pointing reference for the instrument. During an observation the offset between the science target and the guide star will change due to sources such as flexure, differential refraction and non-sidereal tracking rates. GMTIFS uses a beam steering mirror to set the initial offset between science target and guide star and also to correct for changes in offset. In order to reduce image motion from beam steering errors to those comparable to the AO system in the most stringent case, the beam steering mirror is set a requirement of less than 1 milliarcsecond RMS. This corresponds to a dynamic range for both actuators and sensors of better than 1/180,000.

The GMTIFS beam steering mirror uses piezo-walk actuators and a combination of eddy current sensors and interferometric sensors to achieve this dynamic range and control. While the sensors are rated for cryogenic operation, the actuators are not. We report on the results of prototype testing of single actuators, with the sensors, on the bench and in a cryogenic environment. Specific failures of the system are explained and suspected reasons for them. A modified test jig is used to investigate the option of heating the actuator and we report the improved results. In addition to individual component testing, we built and tested a complete beam steering mirror assembly. Testing was conducted with a point source microscope, however controlling environmental conditions to less than 1 micron was challenging. The assembly testing investigated acquisition accuracy and if there was any un-sensed hysteresis in the system. Finally we present the revised beam steering mirror design based on the outcomes and lessons learnt from this prototyping.

A cold chopper is a key device for next generation mid-infrared instruments such as TMT/MICHI. It should achieve fast and accurate position switching with a large chopping throw at cryogenic temperature. To satisfy the requirements, voice coil motors using superconducting MgB₂ wire have been developed. We have made a first prototype of the VCM and carried out its performance measurements such as a transition temperature, transfer functions, and power dissipation in the laboratory. The results are almost consistent with the expectations and the calculations, but some show significant inconsistency. We have also made a next prototype which is small to fit the size of the MICHI chopper. This will be installed to a developing mid-infrared instrument MIMIZUKU and used for actual observations.

EMIR^1,2 (Espectrógrafo Multiobjeto Infra-Rojo) is a wide field multi-object spectrograph already installed in the Nasmyth focus of GTC (Gran Telescopio Canarias). It operates in the near-infrared (NIR), in the wavelength range from 0.9 μm to 2.5 μm and it will include several mechanism working in cryogenic conditions.

A key component of EMIR is the CSU (Configurable Slit Unit), which is a robotic cryo-mechanism used to generate a multi-slit configuration and a long slit on EMIR focal plane when working in spectroscopic mode. The system has 110 sliding bars which can be configured at cryogenic working temperature to create up to 55 slits with a high position accuracy and repeatability. The movement of the bars is performed by an actuator which allows reaching a relatively high speed for the coarse movement and controllable steps up to 2 microns for the fine positioning. This subsystem has been designed and manufactured by the Dutch company Janssen Precision Engineering (JPE) and the Spanish company NTE-SENER. Afterwards, it was thoroughly verified at the IAC (Instituto de Astrofísica de Canarias) facilities.

In this paper, the CSU will be briefly described. One of the more important parts of the CSU is the actuators, which move the bars by means of a stick-slip effect. A set of tests designed for characterizing and improving the robustness and performance of the actuators will be presented. Finally, an overview of the current CSU performance will be presented.

This paper discusses the development, realization and initial characterization of a demonstrator for a cryogenic 'set and forget' deformable mirror. Many optical and cryogenic infrared instruments on modern very and extremely large telescopes aim at diffraction-limited performance and require total wave front errors in the order of 50 nanometers or less. At the same time, their complex optical functionality requires either a large number of spherical mirrors or several complex free-form mirrors. Due to manufacturing and alignment tolerances, each mirror contributes static aberrations to the wave front. Many of these aberrations are not known in the design phase and can only be measured once the system has been assembled. A 'set-and-forget' deformable mirror can be used to compensate for these aberrations, making it especially interesting for systems with complex free-form mirrors or cryogenic systems where access to iterative realignment is very difficult or time consuming.

The mirror with an optical diameter of 200 mm is designed to correct wave front aberrations of up to 2 μm root-mean square (rms). The shape of the wave front is approximated by the first 15 Zernike modes. Finite element analysis of the mirror shows a theoretically possible reduction of the wave front error from 2 μm to 53 nm rms. To produce the desired shapes, the mirror surface is controlled by 19 identical actuator modules at the back of the mirror.

The actuator modules use commercially available Piezo-Knob actuators with a high technology readiness level (TRL). These provide nanometer resolution at cryogenic temperatures combined with high positional stability, and allow for the system to be powered off once the desired shape is obtained. The stiff design provides a high resonance frequency (>200 Hz) to suppress external disturbances.

A full-size demonstrator of the deformable mirror containing 6 actuators and 13 dummy actuators is realized and characterized. Measurement results show that the actuators can provide sufficient stroke to correct the 2 μm rms WFE. The resolution of the actuator influence functions is found to be 0.24 nm rms or better depending on the position of the actuator within the grid. Superposition of the actuator influence functions shows that a 2 μm rms WFE can be accurately corrected with a 38 nm fitting error. Due to the manufacturing method of the demonstrator an artificially large print-through error of 182 nm is observed. The main cause of this print-through error has been identified and will be reduced in future design iterations. After these design changes the system is expected to have a total residual error of less than 70 nm and offer diffraction limited performance (λ14) for wavelengths of 1 μm and above.

The European Solar Telescope, EST, ([1], [2]) is a 4-meter solar telescope to be built in the Canary Islands in the near future. In order to select the best configuration for the EST telescope facilities, thermal and CFD analyses have been carried out to evaluate the seeing degradation produced by the telescope environment. The aim of this study is to calculate the values of optical parameters in different configurations and to find out which one causes the lowest image quality degradation. Starting from the determination of seeing degradation along the optical path by CFD techniques, several configurations have been compared making it possible to decide the future development line for the EST.

DATE5 antenna, which is a 5m telescope for terahertz exploration, will be sited at Dome A, Antarctica. It is necessary to keep high surface accuracy of the primary reflector panels so that high observing efficiency can be achieved. In antenna field, carbon fiber reinforced composite (CFRP) sandwich panels are widely used as these panels are light in weight, high in strength, low in thermal expansion, and cheap in mass fabrication. In DATE5 project, CFRP panels are important panel candidates. In the design study phase, a CFRP prototype panel of 1-meter size is initially developed for the verification purpose. This paper introduces the material arrangement in the sandwich panel, measured performance of this testing sandwich structure samples, and together with the panel forming process. For anti-icing in the South Pole region, a special CFRP heating film is embedded in the front skin of sandwich panel. The properties of some types of basic building materials are tested. Base on the results, the deformation of prototype panel with different sandwich structures and skin layers are simulated and a best structural concept is selected. The panel mold used is a high accuracy one with a surface rms error of 1.4 μm. Prototype panels are replicated from the mold. Room temperature curing resin is used to reduce the thermal deformation in the resin transfer process. In the curing, vacuum negative pressure technology is also used to increase the volume content of carbon fiber. After the measurement of the three coordinate measure machine (CMM), a prototype CFRP panel of 5.1 μm rms surface error is developed initially.

These open-foldable very light-weight domes, based on very strong textile membranes highly tensioned between steel bows, are designed for bad-weather protection and maintenance of instruments for astronomical, meteorological and civil-engineering measurements and have extremely high wind stability. The domes of the GREGOR telescope and the Dutch Open Telescope are the two existing prototypes. Improvements were developed with all parts light-colored to remain cool in solar light. The new specially made connection parts (eyes) between the textile parts are made from white-colored PETP, a very strong and UV-stable synthetic, and have a better geometrical shape giving higher stability. The rubber seal tubes on top of the dome were of black-colored chloride rubber CR (neoprene), strong and UV stable, but very warm in sunlight. New UV-stable EPDM rubber tubes were produced in natural light color. To get this rubber stiff enough to give good sealing, a black-colored stiff EPDM rubber is put inside the light-colored one. Tests were performed and the forces necessary for compression of the rubber tubes were measured. An inside black tube with a circa 1.3 times larger compression force than the original black tubes was applied. The assembling of the black tubes into the light-colored tubes was successfully applied at the DOT and GREGOR domes.

A novel isostatic mounting concept for a space born TMA of the Meteosat Third Generation Infrared Sounder is presented. The telescope is based on a light-weight all-aluminium design. The mounting concept accommodates the telescope onto a Carbon-Fiber-Reinforced Polymer (CRFP) structure. This design copes with the high CTE mismatch without introducing high stresses into the telescope structure. Furthermore a Line of Sight stability of a few microrads under geostationary orbit conditions is provided. The design operates with full performance at a temperature 20K below the temperature of the CFRP structure and 20K below the integration temperature. The mounting will sustain launch loads of 47g. This paper will provide the design of the Back Telescope Assembly (BTA) isostatic mounting and will summarise the consolidated technical baseline reached following a successful Preliminary Design Review (PDR).

The CHEOPS (CHaracterising ExOPlanet Satellite), which is an ESA mission developed in cooperation with Switzerland and a number of other member-states, is the first one dedicated to search for transits by means of ultrahigh precision photometry on bright stars already known to host planets. The optical design is based on a Ritchey-Chretien style telescope to provide a de-focussed image of the target stars.

The telescope’s mirrors M1, M2 as well as the focal plane detector are supported by a thermally controlled CFRP structure suspended on isostatic mounts. The dimensional stability of the structural system supporting the optics is a key requirement as it directly impacts the instrument’s accuracy. The M1 and M2 mirrors are supported by a tubular CFRP telescope design which has been optimized by analyses down to carbon fibre layer level with the support of extensive sample test results for model correlation and accurate dimensional stability predictions. This sample characterization test campaign has been conducted on samples with different carbon fibre layups (orientation and stack sequence) to measure accurately the Coefficient of Thermal Expansion (CTE) over a wide temperature range extending from -80°C to +80°C. Using the correlated Finite Element Model, the fibre orientation layup that minimized the relative displacement between the M1 and M2 mirrors, including the consideration of the thermo-elastic contributions of the isostatic mounts on the overall stability of this optical system, has been identified and selected for the baseline design of the CHEOPS Structure.

A dedicated Structural and Thermal Model (STM2), which was then refurbished to a PFM, was manufactured and tested with an ad hoc setup to verify the overall structural stability of the optical train assembly [2]. The relative distance between M1 and M2 was measured under thermal vacuum conditions using laser interferometer techniques. Thermal cycling tests were initially conducted to eliminate and characterize settling effects. Then, the structure’s stability was measured at three stabilised operational temperatures: -5, -10 and -15°C. The thermally induced M1-M2 misalignment on the optical axis was measured to be between -0.156 and -0.168 micron/°C. Relative mirror tilt and lateral centre shifts were also measured. The obtained focal distance, tilt and centre shift stability between mirrors M1 and M2 were all compliant with the system level requirements such that both an STM and PFM model of the CHEOPS CFRP Structure were successfully qualified and delivered in due time for integration on the spacecraft.

An increasing need for higher resolution for both Science and Earth Observation applications demands a bigger entrance aperture of future optical payloads, leading to large primary mirrors, either monolithic or deployable. Correcting issues linked to manufacturing, integration, launch and use of large light-weighted optics (and associated structures), Active Optics constitutes an enabling technology for future large space instruments. This paper presents the current status of technological developments at ESA in this very promising field.

FAME is a four-year project and part of the OPTICON/FP7 program that is aimed at providing a breakthrough component for future compact, wide field, high resolution imagers or spectrographs, based on both Freeform technology, and the flexibility and versatility of active systems.

Due to the opening of a new parameter space in optical design, Freeform Optics are a revolution in imaging systems for a broad range of applications from high tech cameras to astronomy, via earth observation systems, drones and defense. Freeform mirrors are defined by a non-rotational symmetry of the surface shape, and the fact that the surface shape cannot be simply described by conicoids extensions, or off-axis conicoids. An extreme freeform surface is a significantly challenging optical surface, especially for UV/VIS/NIR diffraction limited instruments.

The aim of the FAME effort is to use an extreme freeform mirror with standard optics in order to propose an integrated system solution for use in future instruments. The work done so far concentrated on identification of compact, fast, widefield optical designs working in the visible, with diffraction limited performance; optimization of the number of required actuators and their layout; the design of an active array to manipulate the face sheet, as well as the actuator design.

In this paper we present the status of the demonstrator development, with focus on the different building blocks: an extreme freeform thin face sheet, the active array, a highly controllable thermal actuator array, and the metrology and control system.

Ground based telescopes suffer from Atmospheric Dispersion that can be compensated for with an Atmospheric Dispersion Corrector (ADC). In the BlackGEM array of 650 mm diameter telescopes, the ADC is fully integrated in the three-lens field corrector and requires lateral displacement of only one lens for a full correction of the Atmospheric Dispersion. This concept results in a very compact and efficient ADC design without the need for any additional optical components. This paper describes the optical trade-offs, optical design and optimization, as well as the mechanical design and implementation of this novel ADC solution.

A novel active mirror technology based on carbon fiber reinforced polymer (CFRP) substrates and replication techniques has been developed. Multiple additional layers are implemented into the design serving various functions. Nanolaminate metal films are used to provide a high quality reflective front surface. A backing layer of thin active material is implemented to provide the surface-parallel actuation scheme. Printed electronics are used to create a custom electrode pattern and flexible routing layer. Mirrors of this design are thin (< 1.0 mm), lightweight (2.7 kg/m²), and have large actuation capabilities. These capabilities, along with the associated manufacturing processes, represent a significant change in design compared to traditional optics. Such mirrors could be used as lightweight primaries for small CubeSat-based telescopes or as meter-class segments for future large aperture observatories. Multiple mirrors can be produced under identical conditions enabling a substantial reduction in manufacturing cost and complexity.

An overview of the mirror design and manufacturing processes is presented. Predictions on the actuation performance have been made through finite element simulations demonstrating correctabilities on the order of 250-300× for astigmatic modes with only 41 independent actuators. A description of the custom metrology system used to characterize the active mirrors is also presented. The system is based on a Reverse Hartmann test and can accommodate extremely large deviations in mirror figure (> 100 μm PV) down to sub-micron precision. The system has been validated against several traditional techniques including photogrammetry and interferometry. The mirror performance has been characterized using this system, as well as closed-loop figure correction experiments on 150 mm dia. prototypes. The mirrors have demonstrated post-correction figure accuracies of 200 nm RMS (two dead actuators limiting performance).

We report on the development of an active mount with an orthogonal actuator matrix offering a stable shape optimization for gratings or mirrors. We introduce the actuator distribution and calculate the accessible Zernike polynomials from their actuator influence function. Experimental tests show the capability of the device to compensate for aberrations of grating substrates as we report measurements of a 110x105 mm² and 220x210 mm² device With these devices, we evaluate the position depending aberrations, long-term stability shape results, and temperature-induced shape variations. Therewith we will discuss potential applications in space telescopes and Earth-based facilities where long-term stability is mandatory.

For the past forty years, optical fibres have found widespread use in ground-based and space-based instruments. In most applications, these fibres are used in conjunction with conventional optics to transport light. But photonics offers a huge range of optical manipulations beyond light transport that were rarely exploited before 2001. The fundamental obstacle to the broader use of photonics is the difficulty of achieving photonic action in a multimode fibre. The first step towards a general solution was the invention of the photonic lantern¹ in 2004 and the delivery of high-efficiency devices (< 1 dB loss) five years on². Multicore fibres (MCF), used in conjunction with lanterns, are now enabling an even bigger leap towards multimode photonics. Until recently, the single-moded cores in MCFs were not sufficiently uniform to achieve telecom (SMF-28) performance. Now that high-quality MCFs have been realized, we turn our attention to printing complex functions (e.g. Bragg gratings for OH suppression) into their N cores. Our first work in this direction used a Mach-Zehnder interferometer (near-field phase mask) but this approach was only adequate for N=7 MCFs as measured by the grating uniformity³. We have now built a Sagnac interferometer that gives a three-fold increase in the depth of field sufficient to print across N ≥ 127 cores. We achieved first light this year with our 500mW Sabre FRED laser. These are sophisticated and complex interferometers. We report on our progress to date and summarize our first-year goals which include multimode OH suppression fibres for the Anglo-Australian Telescope/PRAXIS instrument and the Discovery Channel Telescope/MOHSIS instrument under development at the University of Maryland.

We report on the design and construction of a microlens-array (MLA)-based pupil slicer and double scrambler for MAROON-X, a new fiber-fed, red-optical, high-precision radial-velocity spectrograph for one of the twin 6.5m Magellan Telescopes in Chile. We have constructed a 3X slicer based on a single cylindrical MLA and show that geometric efficiencies of ≥85% can be achieved, limited by the fill factor and optical surface quality of the MLA. We present here the final design of the 3x pupil slicer and double scrambler for MAROON-X, based on a dual MLA design with (a)spherical lenslets. We also discuss the techniques used to create a pseudo-slit of rectangular core fibers with low FRD levels.

We report the results of fiber mode scrambler experiments for the Infra-Red Doppler instrument (IRD) on the Subaru 8.2-m telescope. IRD is a near infrared, high-precision radial velocity (RV) instrument to search for exoplanets around M dwarfs. It is a fiber-fed, high-resolution (R~70000) spectrograph with an Echelle grating and a state-of-the art laser frequency comb. Expected precision of RV measurements is 1m/s. To achieve 1m/s accuracy, we must reduce modal noise, which is intensity instability of light at the end of multimode fibers. Modal noise is caused by interference of finite number of propagating modes of light. This noise can cause false RV signals, which reduce the accuracy of RV measurements. A mode scrambler is a mechanism to reduce modal noise. However, the best mode scrambler system at near infrared wavelengths is still unknown. Thus, we tested many kinds of mode scramblers, various length fibers, a double scrambler, and octagonal fibers, as static scramblers. We also tested dynamic scramblers, which make output uniform by moving optical fibers dynamically. We report the effects of these mode scramblers.

In order to detect Earth-like planets around nearby red dwarfs (in particular late-M stars), it is crucial to conduct precise radial velocity measurements at near-infrared wavelengths where these stars emit most of the light. We have been developing the Infrared Doppler (IRD) spectrograph which is a high dispersion spectrograph for the Subaru telescope. To achieve 1m/s RV measurement precision, we have developed a direct generation of laser frequency comb (LFC) that uses high-repetition-rate pump pulse synthesized by a line-by-line pulse-shaping technique. Our LFC generator has some advantages including simple and easy frequency stabilization, all fiber-optic configuration, and broadband calibration by the precise frequency shift of all modes in the LFC. We have successfully generated a 12.5-GHz-spaced comb spanning over 700 nm from 1040 to 1750 nm. The frequency stability was measured by optically heterodyning the comb with an acetylene-stabilized laser at 1542 nm as a reference light. The LFC showed a frequency stability of less than 0.2 MHz and an almost constant spectrum profile for 6 days. The original LFC that has just produced from highly nonlinear fibers needs some optical processing including spectrum shaping, depolarization, and a mode scramble in a multi-mode fiber before it is input into a spectrograph for the calibration. We have investigated the optical processing of the LFC which is necessary for the precise spectrograph calibration. Keywords: laser frequency comb, infrared, spectrograph, Doppler shift

In order to track the stellar objects in fiber spectroscopic telescopes, measuring the fiber positions is necessary, which is currently unsolved due to the large number of data. In this paper, we propose a novel measure method based on the Field Programmable Gate Arrays (FPGA). Firstly, the fiber spots are obtained from the complicated original images by preprocessing including the median filtering technique to remove the image noise and the correlation operation technique to enhance the fiber spot characteristic. Then, a novel fast connected component labeling technique is employed to acquire the accurate fiber positions. The design of the image processing system is realized by a five-stage pipeline technique based on the FPGA, thus the image processing speed is greatly improved and meanwhile the real-time calculation of the fiber positions is fulfilled.

Optical fibers are a key component for high-resolution spectrographs to attain high precision in radial velocity measurements. We present a custom fiber with a novel core geometry - a 'D'-shape. From a theoretical standpoint, such a fiber should provide superior scrambling and modal noise mitigation, since unlike the commonly used circular and polygonal fiber cross sections, it shows chaotic scrambling. We report on the fabrication process of a test fiber and compare the optical properties, scrambling performance, and modal noise behaviour of the D-fiber with those of common polygonal fibers.

This paper presents a design proposal for controlling the five thousand fiber positioners within the focal plate of the DESI instrument. Each of these positioners is a robot which allows positioning its optic fiber with a resolution within the range of few microns. The high number and density of these robots poses a challenge for handling the communication from a central control device to each of these five thousand. Furthermore, an additional restriction applies as the required time to communicate to every robot of its position must be smaller than a second. Additionally. a low energy consumption profile is also desired.

Both wireless and wired communication protocols have been evaluated, proposing single-technology-based architectures and hybrid ones (a combination of them). Among the wireless solutions, ZigBee and CyFi have been considered. Using simulation tools these wireless protocols have been discarded as they do not allow an efficient communication. The studied wired protocols comprise I2C, CAN and Ethernet.

The best solution found is a hybrid multilayer architecture combining both Ethernet and I2C. A 100 Mbps Ethernet based network is used to communicate the central control unit with ten management boards. Each of these boards is a low-cost, low-power embedded device that manages a thirty six degrees sector of the sensing plate. Each of these boards receives the positioning data for five hundred robots and communicate with each one through a fast mode plus I2C bus. This proposal allows to communicate the positioning information for all five thousand robots in 350 ms total.

TAIPAN will conduct a stellar and galaxy survey of the Southern sky. The TAIPAN positioner is being developed as a prototype for the MANIFEST instrument on the GMT. The design for TAIPAN incorporates 150 optical fibres (with an upgrade path to 300) situated within independently controlled robotic positioners known as Starbugs. Starbugs allow precise parallel positioning of individual fibres, thus significantly reducing instrument configuration time and increasing the amount of observing time. Presented is an engineering overview of the UKST upgrade of the completely new Instrument Spider Assembly utilized to support the Starbug Fibre Positioning Robot and current status of the Starbug itself.

The WIYN Spectrograph for Doppler Monitoring (WISDOM) was a concept responding to NASA's solicitation for an extreme precision radial velocity instrument for the 3.5 meter WIYN telescope on Kitt Peak in Arizona. In order to meet the spectral resolution requirement of R = 110,000 while maintaining good throughput and a manageable beam diameter, the front end design of the instrument employed a pupil slicing technique wherein a collimated beam is sliced and fed to six separate fibers. This paper presents the optical and mechanical design of the pupil slicer subassembly, a unique method of dealing with thermally induced defocus error, and the methods and results of aligning a prototype.

Fiber Bragg gratings are used in astronomy for their ability to suppress narrow atmospheric emission lines of temporally varying brightness before the light is dispersed. These gratings can only operate in a single-mode fiber as the suppressed wavelength depends on mode velocity in the core. Recent experiments with fibers containing multiple single-moded cores have demonstrated the potential for inscribing identical gratings across all cores in a single pass. We have already improved the uniformity of gratings in 7-core fibers via modifications to the writing process; further progress can be achieved by tuning the gratings of the outer and inner cores relative to one another. Our eventual goal is to make the entire fiber suppress one wavelength to a depth of 30 dB or greater. By coating the fiber in a heat-conductive material with a high expansion coefficient, we can examine the effects of temperature and strain on the spectral response of each core. In this paper we present methods and results from experiments concerning the post-write tuning of gratings in multicore fibers.

WEAVE is a new wide-field spectroscopy facility proposed for the prime focus of the 4.2m William Herschel Telescope. The facility comprises a new 2-degree field of view prime focus corrector with a 1000-multiplex fibre positioner, a small number of individually deployable integral field units, and a large single integral field unit. The IFUs (Integral Field Units) and the MOS (Multi Object Spectrograph) fibres can be used to feed a dual-beam spectrograph that will provide full coverage of the majority of the visible spectrum in a single exposure at a spectral resolution of ~5000 or modest wavelength coverage in both arms at a resolution ~20000. The instrument is expected to be on-sky by the first quarter of 2018 to provide spectroscopic sampling of the fainter end of the Gaia astrometric catalogue, chemical labeling of stars to V~17, and dedicated follow up of substantial numbers of sources from the medium deep LOFAR surveys. After a brief description of the Fibre System, we describe the fibre test bench, its calibration, and some test results. We have to verify 1920 fibres from the MOS bundles and 740 fibres from the mini-IFU bundles with the test bench. In particular, we present the Focal Ratio Degradation of a cable.

The Australian Astronomical Observatory's 'tilting spine' fibre positioning technology has been redeveloped to provide superior performance in a smaller package. The new design offers demonstrated closed-loop positioning errors of <2.8 μm RMS in only five moves (~10 s excluding metrology overheads) and an improved capacity for open-loop tracking during observations. Tilt-induced throughput losses have been halved by lengthening spines while maintaining excellent accuracy. New low-voltage multilayer piezo actuator technology has reduced a spine's peak drive amplitude from ~150V to <10V, simplifying the control electronics design, reducing the system's overall size, and improving modularity. Every spine is now a truly independent unit with a dedicated drive circuit and no restrictions on the timing or direction of fibre motion.

After having demonstrated that an IFU, attached to a microscope rather than to a telescope, is capable of differentiating complex organic tissue with spatially resolved Raman spectroscopy, we have launched a clinical validation program that utilizes a novel optimized fiber-coupled multi-channel spectrograph whose layout is based on the modular MUSE spectrograph concept. The new design features a telecentric input and has an extended blue performance, but otherwise maintains the properties of high throughput and excellent image quality over an octave of wavelength coverage with modest spectral resolution. We present the opto-mechanical layout and details of its optical performance.

TAIPAN will conduct a stellar and galaxy survey of the Southern sky. The TAIPAN positioner is being developed as a prototype for the MANIFEST instrument on the GMT. The TAIPAN Spectrograph is an AAO designed all-refractive 2-arm design that delivers a spectral resolution of R>2000 over the wavelength range 370-870 nm. It is fed by a custom fibre cable from the TAIPAN Starbugs positioner. The design for TAIPAN incorporates 150 optical fibres (with an upgrade path to 300). Presented is an engineering overview of the UKST Fibre Cable design used to support Starbugs, the custom slit design, and the overall design and build plan for the TAIPAN Spectrograph.

We describe overview of fabrication methods and measurement results of test fabrications of optical surfaces for an integral field unit (IFU) for Simultaneous color Wide-field Infrared Multi-object Spectrograph, SWIMS, which is a first-generation instrument for the University of Tokyo Atacama Observatory 6.5-m telescope. SWIMS-IFU provides entire near-infrared spectrum from 0.9 to 2.5 μm simultaneously covering wider field of view of 17" × 13" compared with current near-infrared IFUs. We investigate an ultra-precision cutting technique to monolithically fabricate optical surfaces of IFU optics such as an image slicer. Using 4- or 5-axis ultra precision machine we compare the milling process and shaper cutting process to find the best way of fabrication of image slicers. The measurement results show that the surface roughness almost satisfies our requirement in both of two methods. Moreover, we also obtain ideal surface form in the shaper cutting process. This method will be adopted to other mirror arrays (i.e. pupil mirror and slit mirror, and such monolithic fabrications will also help us to considerably reduce alignment procedure of each optical elements.

The VLT/SPHERE instrument includes a unique long-slit spectroscopy (LSS) mode coupled with Lyot coronagraphy dedicated to the spectral characterization of directly imaged giant exoplanets. The performance of this mode is limited by its non-optimal coronagraph, but in a previous work we demonstrated that it could be significantly improved at small inner-working angles using the stop-less Lyot coronagraph (SLLC). A prototype of the SLLC was installed in VLT/SPHERE in 2014 during the reintegration of the instrument in Paranal, and it was extensively tested in 2015 to characterize its performance. The performance is tested in both imaging and spectroscopy using data acquired on the internal source of SPHERE. In imaging, we obtain a raw contrast gain of a factor 10 at 0.3" with the SLLC. We also demonstrate that no Lyot stop is required to reach the full performance, which validates the SLLC concept. Comparison with a realistic simulation model shows that we are currently limited by the internal phase aberrations of SPHERE. In spectroscopy, we obtain a gain of 1 mag in a limited range of angular separations. Simulations show that although the main limitation comes from phase errors, the performance in the non-SLLC case is very close to the ultimate limit of the LSS mode. We present the very first on-sky data with the SLLC, which appear extremely promising for the future scientific exploitation of an apodized LSS mode in SPHERE. Finally, we explore a new possibility for the speckle subtraction in the LSS mode that could significantly improve the data analysis with respect to methods based on spectral differences.

The advent of 30 m class Extremely Large Telescopes will require spectrographs of unprecedented spectral resolution in order to meet ambitious science goals, such as detecting Earth-like exoplanets via the radial velocity technique. The consequent increase in the size of the spectrograph makes it challenging to ensure their optimal environmental stabilization and precise spectral calibration. The multimode optical fibers used to transport light from the telescope focal plane to the separately housed environmentally stabilized spectrograph introduces modal noise. This phenomena manifests as variations in the light pattern at the output of the fiber as the input coupling and/or fiber position changes which degrades the spectrograph line profile, reducing the instrument precision. The photonic lantern is a guided wave transition that efficiently couples a multimode point spread function into an array of single modes. If arranged in a linear array at the input of the spectrograph these single modes can in principle provide a diffraction-limited mode noise free spectra in the dispersion axis. In this paper we describe the fabrication and throughput performance of the hybrid reformatter. This device combines the proven low-loss performance of a multicore fiber-based photonic lantern with an ultrafast laser inscribed three-dimensional waveguide interconnect that performs the reformatting function to a diffraction-limited pseudo-slit. The device provided an in laboratory throughput of 65 ± 2% at 1550 ± 20 nm and an on-sky throughput of 53 ± 4% at 1530 ± 80 nm using the CANARY adaptive optics system at the William Herschel Telescope.

This paper reports on the modal noise characterisation of a hybrid reformatter. The device consists of a multicore-fibre photonic lantern and an ultrafast laser-inscribed slit reformatter. It operates around 1550 nm and supports 92 modes. Photonic lanterns transform a multimode signal into an array of single-mode signals, and thus combine the high coupling efficiency of multimode fibres with the diffraction-limited performance of single-mode fibres. This paper presents experimental measurements of the device point spread function properties under different coupling conditions, and its throughput behaviour at high spectral resolution. The device demonstrates excellent scrambling but its point spread function is not completely stable. Mode field diameter and mode bary-centre position at the device output vary as the multicore fibre is agitated due to the fabrication imperfections.

We report on the construction and testing of a vacuum-gap Fabry-Perot etalon calibrator for high precision radial velocity spectrographs. The etalon is referenced against hyper fine transitions of rubidium to provide a precise wavelength calibrator for MAROON-X, a new fiber-fed, red-optical, high-precision radial-velocity spectrograph currently under construction for one of the twin 6.5m Magellan Telescopes in Chile. We demonstrate a turnkey system, ready to be installed at any current and next generation radial velocity spectrograph that requires calibration over a wide spectral band-pass. Uncertainties in the position of one etalon line are at the 10 cm s^-1 level in individual measurements taken at 4 Hz. Our long-term stability is mainly limited by aging effects of the spacer material Zerodur, which imprints a 12 cm s^-1 daily drift. However, as the etalon position is traced by the rubidium reference with a precision of <3 cm s^-1 for integration times longer than 10s, we can fully account for this effect at the RV data reduction level.

We report about our latest achievements to realize the diffraction gratings during the development activities for a future Earth observation high resolution spectrometer studied by ESA. The gratings are manufactured by electron beam lithography on fused silica substrates. The optical performance is considerably increased by applying a dedicated high refractive index coating to the grating structure using atomic layer deposition (ALD). Thus, we were able to achieve diffraction efficiencies larger than 75% averaged over both linear polarizations states, i.e. TE and TM. At the same time, the polarization sensitivity is well below 10% in both cases. Finally, the diffraction gratings for the SWIR-1 spectral channel were bonded on a massive prism substrate in order to realize a GRISM element. This process was achieved by direct fused silica bonding performed under atmospheric pressure within special mechanical equipment designed and constructed particularly for this purpose.

The CRIRES+ project attempts to upgrade the CRIRES instrument into a cross dispersed Echelle spectrograph with a simultaneous recording of 8-10 diffraction orders. In order to transform the CRIRES spectrograph into a cross-dispersing instrument, a set of six reflection gratings, each one optimized for one of the wavelength bands CRIRES+ will operate in (YJHKLM), will be used as cross dispersion elements in CRIRES+. Due to the upgrade nature of the project, the choice of gratings depends on the fixed geometry of the instrument. Thus, custom made gratings would be required to achieve the ambitious design goals. Custom made gratings have the disadvantage, though, that they come at an extraordinary price and with lead times of more than 12 months. To mitigate this, a set of off-the-shelf gratings was obtained which had grating parameters very close to the ones being identified as optimal. To ensure that the rigorous specifications for CRIRES+ will be fulfilled, the CRIRES+ team started a collaboration with the Physikalisch-Technische Bundesanstalt Berlin (PTB) to characterize gratings underconditions similar to the operating conditions in CRIRES+ (angle of incidence, wavelength range).

The respective test setup was designed in collaboration between PTB and the CRIRES+ consortium. The PTB provided optical radiation sources and calibrated detectors for each wavelength range. With this setup, it is possible to measure the absolute efficiency of the gratings both wavelength dependent and polarization state dependent in a wavelength range from 0.9 μm to 6 μm.

ESA Euclid mission is designed to map the geometry of the dark Universe. The NISP (Near Infrared Spectro- Photometer) is one of its two instruments dedicated to NIR with two main observing modes: the photometric mode and the spectroscopic mode, for the acquisition of slitless dispersed images using four low resolution grisms: three "red" grisms for 1250-1850nm, and one "blue" grism for 920-1300nm. The NISP grisms are complex optical components that combine four main functions: a grism done by the grating on the prism hypotenuse, a spectral filter done by a multilayer filter deposited on the first surface of the prism, a focus function done by a curved surface and a spectral wavefront correction done by the grating with curved grooves. This specific grating is made thanks to a new technic developed with SILIOS Technologies to manufacture a resin-free grating. The optical component is glued onto a mechanical ring, designed to survive to 60g DLL and to keep optical performance at 130K. The design and manufacturing of these components represent an important challenge to obtain the best performances with very constraining requirements. We will present the performance obtained on scale-1 prototypes of the filter, the grating and the mount manufactured to validate the final design choices and used to make the necessary trade-off during the development phase. All the prototypes have shown very good optical performances and have withstood vibrations and vacuum cryogenic tests that confirm the feasibility of NISP grisms and prepare the next phase for the procurement and tests of NISP grism flight models.

Exploitation of far ultraviolet (FUV, 100-200 nm) observations extends to most areas of modern astronomy, from detailed observations of Solar System objects, the interstellar medium, exoplanets, stars and galaxies, to studies of crucial cosmological relevance. Despite several developments in recent decades, yet many observations are not possible due to technical limitations, of which one of the most important is the lack of optical coatings with high throughput. Development and optimization of such efficient FUV coatings have been identified in several roadmap reports as a key goal for future missions. The success of this development will ultimately improve the performance of nowadays feasible optical instruments and will enable new scientific imaging capabilities.

GOLD’s research is devoted to developing novel coatings with enhanced performance for space optics. Several deposition systems are available for the deposition of multilayer coatings. A deposition system was developed to deposit FUV coatings to satisfy space requirements. It consists of a 75-cm-diameter deposition chamber pumped with a cryo-pump and placed in an ISO-6 clean room. This chamber is available for deposition by evaporation of top-requirement coatings such as Al/ MgF₂ mirrors or (Al/MgF₂)_n multilayer coatings for transmittance filters. A plan to add an Ion-Beam-Sputtering system in this chamber is under way.

In this and other chambers at GOLD the following FUV coatings can be prepared:

Transmittance filters based on (Al/MgF₂)_n multilayer coatings. These filters can be designed to have a peak at the FUV spectral line or band of interest and a high peak-to-visible transmittance ratio. Filters can be designed with a peak transmittance at a wavelength as short as 120 nm and with a transmittance in the visible smaller than 10^-5.

Narrowband reflective coatings peaked close to H Lyman β (102.6 nm) with a reflectance at H Lyman α (121.6 nm) two orders of magnitude below the one at 102.6 nm. Other potential spectral lines at which these coatings could be peaked are the OVI doublet (103.2, 103.8 nm).

Narrowband reflective mirrors based on (MgF₂/LaF₃)_n multilayers peaked at a wavelength as short as 120 nm. Target wavelengths include lines of high interest for space observations, such as H Lyman α (121.6 nm), OI (130.4 and 135.6 nm), CIV (154.8, 155.1 nm), among others.

Coating-based linear polarizers tuned at H Lyman α (121.6 nm) both based on reflectance or on transmittance. Reflective polarizers present a high efficiency. Transmissive polarizers have a more modest peak performance compared to reflective polarizers; however, they involve spectral filtering properties to reject the long FUV and even more the near UV to the IR, which turn them competitive compared to reflective polarizers.

In this communication we present a summary of our research on the above FUV coatings developed at GOLD.

Over the past few years the advent of atomic layer deposition (ALD) technology has opened new capabilities to the field of coatings deposition for use in optical elements. At the same time, there have been major advances in both optical designs and detector technologies that can provide orders of magnitude improvement in throughput in the far ultraviolet (FUV) and near ultraviolet (NUV) passbands. Recent review work has shown that a veritable revolution is about to happen in astronomical diagnostic work for targets ranging from protostellar and protoplanetary systems, to the intergalactic medium that feeds gas supplies for galactic star formation, and supernovae and hot gas from star forming regions that determine galaxy formation feedback. These diagnostics are rooted in access to a forest of emission and absorption lines in the ultraviolet (UV)^[1], and all that prevents this advance is the lack of throughput in such systems, even in space-based conditions. We outline an approach to use a range of materials to implement stable optical layers suitable for protective overcoats with high UV reflectivity and unprecedented uniformity, and use that capability to leverage innovative ultraviolet/optical filter construction to enable astronomical science. These materials will be deposited in a multilayer format over a metal base to produce a stable construct. Specifically, we will employ the use of PEALD (plasma-enhanced atomic layer deposition) methods for the deposition and construction of reflective layers that can be used to construct unprecedented filter designs for use in the ultraviolet.

We present progress in efforts underway at the University of California Observatories to develop high performance durable silver-based mirror coatings for telescope and instruments. Silver-based coatings are extremely prone to tarnish and/or corrosion, and successful coatings depend not only on the materials used but also the deposition processes employed. Our physical vapor deposition (PVD) chamber allows both sputtering and ion-assisted e-beam depositions for head-to-head comparison of deposition processes, and we present results of these comparisons. In this paper, we review the problem and discuss our recent activities and findings. We discuss a systematic study to determine which oxides, nitrides and fluorides provide the best protection in environmental tests. We present initial results into the effects of stress in our specific thin films, and thee effects of stress on mirror coating durability. We also discuss studies using Atomic Layer Deposition (ALD) over-coating of Ag, and we describe a large ALD research chamber currently under construction that will demonstrate ALD processes on larger substrates (70 cm diameter).

The Observatorio Astrofisico de Javalambre in Spain will conduct an all-sky astronomical survey using multi-bands, where optical filters are needed. These filters are narrow bandpass steep edge filters (FWHM = 14.5 nm) in a spectrum between 390 to 920 nm with 10.0 nm steps. In order to fulfill the demanding requirements for final scientific image quality and transmitted wavefront error a new white-light Shack Hartmann sensor and difficult refractive index measurements of the sub-assembly were needed. In addition due to the spectral requirements the design and manufacturing of the filters were pushed at its technological limit.

Recently Safran Reosc worked and progressed on various thin film technology for:

Large mirrors with low stress and stable coatings.

Large lens elements with strong curvature and precise layer specifications.

Large filters with high spectral response uniformity specifications.

IR coatings with low stress and excellent resistance to cryogenic environment for NIR to LWIR domains.

Pixelated coatings.

Results will be presented and discussed on the basis of several examples.

Deformable mirrors (DMs) are an enabling and mission-critical technology in any coronagraphic instrument designed to directly image exoplanets. A new ferro fluid deformable mirror technology for high-contrast imaging is currently under development at Princeton, featuring a flexible optical surface manipulated by the local electromagnetic and global hydraulic actuation of a reservoir of ferro fluid. The ferro fluid DM is designed to prioritize high optical surface quality, high-precision/low-stroke actuation, and excellent low-spatial-frequency performance - capabilities that meet the unique demands of high-contrast coronagraphy in a space-based platform. To this end, the ferro-fluid medium continuously supports the DM face sheet, a configuration that eliminates actuator print-through (or, quilting) by decoupling the nominal surface figure from the geometry of the actuator array. The global pressure control allows independent focus actuation. In this paper we describe an analytical model for the quasi-static deformation response of the DM face sheet to both magnetic and pressure actuation. These modeling efforts serve to identify the key design parameters and quantify their contributions to the DM response, model the relationship between actuation commands and DM surface-profile response, and predict performance metrics such as achievable spatial resolution and stroke precision for specific actuator configurations. Our theoretical approach addresses the complexity of the boundary conditions associated with mechanical mounting of the face sheet, and makes use of asymptotic approximations by leveraging the three distinct length scales in the problem - namely, the low-stroke (~nm) actuation, face sheet thickness (~mm), and mirror diameter (cm). In addition to describing the theoretical treatment, we report the progress of computational multi physics simulations which will be useful in improving the model fidelity and in drawing conclusions to improve the design.

Current state-of-the-art high contrast imaging instruments take advantage of a number of elegant coronagraph designs to suppress starlight and image nearby faint objects, such as exoplanets and circumstellar disks. The ideal performance and complexity of the optical systems depends strongly on the shape of the telescope aperture. Unfortunately, large primary mirrors tend to be segmented and have various obstructions, which limit the performance of most conventional coronagraph designs. We present a new family of vortex coronagraphs with numerically-optimized gray-scale apodizers that provide the sensitivity needed to directly image faint exoplanets with large, segmented aperture telescopes, including the Thirty Meter Telescope (TMT) as well as potential next-generation space telescopes.

We introduce a new technological framework for high-contrast coronagraphy, namely digital adaptive coronagraphy (DAC) using spatial light modulators (SLMs), taking advantage of recent advances in this technology. We present proof-of-principle experimental results in the visible, using a transmissive twisted nematic liquid crystal SLM display to show that SLMs can be successfully implemented as focal-plane phase-mask coronagraphs (4QPM, 8OPM,...), and that the technology is essentially in place to address realistic instrumental configurations. We explore a specific application where SLM-based adaptive coronagraphy might be particularly competitive, which is direct imaging of multiple stars systems, by simultaneously nulling multiple point sources in the field. Using a simple approach to compute a brightness-weighted synthetized coronagraphic phase map, we show that in the case of binaries the contrast gain over using a regular phase map can exceed 4 stellar magnitudes for a 1:1 binaries down to separation as close as 1 λ/D. Thanks to video-rate update frequency of the SLM, the technique is in principle compatible with sky rotation in the case of altitude-azimuth telescope mounts, and can address multiple target configurations with no actual mechanical or hardware change.

The use of a starshade is one technique to perform high contrast imaging with space-based telescopes. The primary function of a starshade is to suppress light from a target star in order to image its orbiting planets. In order to provide the proper apodization function the edges of the starshade must follow a precise in-plane profile. However of equal importance is the issue of light from our own sun scattering off of the edges and entering the telescope. A method to alleviate this problem is to make the edges extremely sharp (< 1 μm terminal radius) such that the area available for scattering is minimized. The combination of these two requirements, along with the need to integrate the edges into a 30-40 m dia. deployable structure, present a number of significant engineering challenges. Substrate etching techniques are used to obtain both the intended profile as well as the edge sharpness. Current efforts implement an isotropic etching process on thin metal substrates. This paper discusses the progress towards producing a sharp optical edge at the coupon level. Samples have been characterized using scanning electron microscopy as well as a custom testbed to assess their scattered-light performance.

The Pyramid Sensor (PS) is based on the Focault knife-edge test, yielding then, in geometrical approximation, only the sign of the wavefront slope. To provide linear measurements of the wavefront slopes the PS relies on a technique known as modulation, which also plays a central role to improve the linear range of the pyramid WFS, very small in the nonmodulated case. In the main PS using modulation so far, this task is achieved by moving optical components in the WFS, increasing the complexity of the system. An attractive idea to simplify the optical and mechanical design of a pyramid WFS is to work without any dynamic modulation.

This concept was only merely described and functionally tested in the framework of MAD, and subsequently, with a holographic diffuser. The latter produce a sort of random distribution of the light coming out from the pupil plane, leading to sort of inefficient modulation, as most of the rays are focused in the central region of the light diffused by such device. The bi-dimensional original grating is, in contrast, producing a well defined deterministic distribution of the light onto a specifically shaped pattern. A crude option has been already discussed as a possibility, and it is here generalized to holographic plates leading to various distribution of lights, including a circle whose diameter would match the required modulation pattern, or more cost effective approaches like the one of a square pattern. These holographic diffusers would exhibit also zero-th and high order patterns and the actual size of the equivalent modulation would be linearly wavelength dependent, leading to colour effects that requires a careful handling in order to properly choose the right amount of equivalent modulation.

A new stray light coating, called J-Black, has been developed for NASA's Stratospheric Observatory for Infrared Astronomy (SOFIA). The coating is a layered composition of Nextel-Suede 3101 primers and top coats and silicon carbide grit. J-Black has been applied to large areas of the SOFIA airborne telescope and is currently operating within the open cavity environment of the Boeing 747. Over a series of discrete filter bands, from 0.4 to 21 microns, J-Black optical and infrared reflectivity performance is compared with other available coatings. Measured total reflectance values are less than 2% at the longest wavelengths, including at high incidence angles. Detailed surface structure characteristics are also compared via electron and ion microscopy. Environmental tests applicable for aerospace applications are presented, as well as the detailed steps required to apply the coating.

Atomic Layer Deposition (ALD) can create conformal, near stoichiometric and pinhole free transmissive metal fluoride coatings to protect reflective aluminum films. Spectral performance of astronomical mirror coatings strongly affect the science capabilities of astronomical satellite missions. We are utilizing ALD to create a transmissive overcoat to protect aluminum film mirrors from oxidation with the goal of achieving high reflectance (> 80%) from the UV (~100 nm) to the IR (~2,000 nm). This paper summarizes the recent developments of ALD aluminum fluoride (AlF₃) coatings on Al. Reflectance measurements of aluminum mirrors protected by ALD AlF₃ and future applications are discussed. These measurements demonstrate that Al + ALD AlF₃, even with an interfacial oxide layer of a few nanometers, can provide higher reflectance than Al protected by traditional physical vapor deposited MgF₂ without an oxide layer, below ~115 nm.

Immersion grating is a powerful optical device for thee infrared high-resolution spectroscope. Germanium (GGe) is the best material for a mid-infrared immersion grating because of Ge has very large reflective index (n=4.0). On the other hands, there is no practical Ge immersion grating under 5umm use. It was very difficult for a fragile IR crystal to manufacture a diffraction grating precisely. Our original free-forming machine has accuracy of a few nano-meter in positioning and stability. We already fabricated the large CdZnTe immersion grating. (Sukegawa et al. (2012), Ikeda et al. (2015)) Wee are developing Ge immersion grating that can be a good solution for high-resolution infrared spectroscopy with the large ground-based/space telescopes. We succeeded practical Ge immersion grating with the grooved area off 75mm (ruled direction) x 119mm (grove width) and the blaze angle of 75 degrees. Our astronomical large Ge immersion grating has the grooved area of 155mm (ruled direction) x 41mmm (groove width) and groove pitch off 91.74um. We also report optical performance of astronomical large Ge immersion grating with a metal coating on the diffraction surface.

SCHOTT was one of the interference filters inventors starting around 1935. Based on this legacy optical bandpass filters were design, manufactured, and integrated into optical instruments in satellites. In addition a special blocking coating was developed reducing cross talk and ghost. For ground based telescopes steep-edge narrow bandpass filters with low transmitted wavefront error and about 100 mm x 100 mm size were manufactured pushing the filter design and the technology to its limits. The reached results for design and measurements will be shown on an H-alpha filter.

Ultrafast laser inscription is a versatile manufacturing technique which can be used to modify the refractive index of various glasses on a microscopic scale. This enables the production of a number of photonic devices such as waveguides, beam-splitters, photonic lanterns, and diffraction gratings. In this paper, we report on the use of ultrafast laser inscription to fabricate volume phase transmission gratings in mid-infrared transmitting chalcogenide glass.

We describe the optimisation of the laser inscription process parameters enhancing grating performances via the combination of spectrally resolved grating transmission measurements and theoretical analysis models. The first order diffraction efficiency of the gratings was measured at mid-infrared wavelengths (3-5 μm), and found to exceed 60% at the Littrow blaze wavelength, compared to a substrate external transmittance of 67%. This impressive result implies the diffraction efficiency should exceed 90% for a grating substrate treated with an anti-reflection coating. There is excellent agreement between the modelled grating efficiency and the measured data, and from a least squares fit to the measured data the refractive index modulation achieved during the inscription process is inferred. These encouraging initial results demonstrate that ultrafast laser inscription of chalcogenide glass may provide a potential new and alternative technology for the manufacture of astronomical diffraction gratings for use at near-infrared and mid-infrared wavelengths.

A new technique based on photolithographic processes of thin-film optical pass band coatings on a monolithic substrate has been applied to the filters of the Focal Plane Assembly (FPA) of the Colour and Stereo Surface Imaging System (CaSSIS) that will fly onboard of the ExoMars Trace Gas Orbiter to be launched in March 2016 by ESA.

The FPA including is one of the spare components of the Simbio-Sys instrument of the Italian Space Agency (ASI) that will fly on ESA’s Bepi Colombo mission to Mercury. The detector, developed by Raytheon Vision Systems, is a 2kx2k hybrid Si-PIN array with a 10 μm pixel. The detector is housed within a block and has filters deposited directly on the entrance window. The window is a 1 mm thick monolithic plate of fused silica. The Filter Strip Assembly (FSA) is produced by Optics Balzers Jena GmbH and integrated on the focal plane by Leonardo-Finmeccanica SpA (under TAS-I responsibility). It is based on dielectric multilayer interference coatings, 4 colour bands selected with average in-band transmission greater than 95 percent within wavelength range (400-1100 nm), giving multispectral images on the same detector and thus allows CaSSIS to operate in push-frame mode.

The Field of View (FOV) of each colour band on the detector is surrounded by a mask of low reflective chromium (LRC), which also provides with the straylight suppression required (an out-of-band transmission of less than 10^-5/nm). The mask has been shown to deal effectively with cross-talk from multiple reflections between the detector surface and the filter.

This paper shows the manufacturing and optical properties of the FSA filters and the FPA preliminary on-ground calibration results.

As a transmission grating, a surface-relief (SR) grating with sawtooth shaped ridges and volume phase holographic (VPH) grating are widely used for instruments of astronomical observations. However the SR grating is difficult to achieve high diffraction efficiency at high angular dispersion, and the VPH grating has low diffraction efficiency in high diffraction orders. We propose novel gratings that solve these problems. We introduce the hybrid grism which combines a high refractive index prism with a replicated transmission grating, which has sawtooth shaped ridges of an acute apex angle. The birefringence VPH (B-VPH) grating which contains an anisotropic medium, such as a liquid crystal, achieves diffraction efficiency up to 100% at the first diffraction order for natural polarization and for circular polarization. The quasi-Bragg (QB) grating which consists of long rectangular mirrors aligned in parallel precisely, like a window blind, achieves diffraction efficiency of 60% or more in higher than the 4th diffraction order. The volume binary (VB) grating with narrow grooves also achieves diffraction efficiency of 60% or more in higher than the 6th diffraction order. The reflector facet transmission (RFT) grating which is a SR grating with sawtooth shaped ridges of an acute apex angle achieves diffraction efficiency up to 80% in higher than the 4th diffraction order.

The optical system of the hyperspectral imager of the Environmental Mapping and Analysis Program (EnMAP) consists of a three-mirror anastigmat (TMA) and two independent spectrometers working in the VNIR and SWIR spectral range, respectively. The VNIR spectrometer includes a spherical NiP coated Al6061 mirror that has been ultra-precisely diamond turned and finally coated with protected silver as well as four curved fused silica (FS) and flint glass (SF6) prisms, respectively, each with broadband antireflection (AR) coating, while the backs of the two outer prisms are coated with a high-reflective coating. For AR coating, plasma ion assisted deposition (PIAD) has been used; the high-reflective enhanced Ag-coating on the backside has been deposited by magnetron sputtering. The SWIR spectrometer contains four plane and spherical gold-coated mirrors, respectively, and two curved FS prisms with a broadband antireflection coating. Details about the ultra-precise manufacturing of metal mirrors and prisms as well as their coating are presented in this work.

Volume phase holographic (VPH) gratings are proven dispersing elements in astronomical spectrographs over the visible spectrum. VPH gratings have also been successfully deployed for use at cryogenic temperatures. Recent advances in production technology now permit the production of gratings for use in the near infrared up to 2450 nm at cryogenic conditions. This paper describes the requirements of VPH gratings for use in the H (wavelengths from 1500 nm to 1800 nm) and K (wavelengths from 1950 nm to 2450 nm) bands, gives the theoretical performances of diffraction efficiency for the production designs and presents the measured performances on the production gratings

A large format germanium immersion grating was flycut with a single-point diamond tool on the Precision Engineering Research Lathe (PERL) at the Lawrence Livermore National Laboratory (LLNL) in November – December 2015. The grating, referred to as 002u, has an area of 59 mm x 67 mm (along-groove and cross-groove directions), line pitch of 88 line/mm, and blaze angle of 32 degree. Based on total groove length, the 002u grating is five times larger than the previous largest grating (ZnSe) cut on PERL, and forty-five times larger than the previous largest germanium grating cut on PERL. The key risks associated with cutting the 002u grating were tool wear and keeping the PERL machine running uninterrupted in a stable machining environment. This paper presents the strategies employed to mitigate these risks, introduces pre-machining of the as-etched grating substrate to produce a smooth, flat, damage-free surface into which the grooves are cut, and reports on trade-offs that drove decisions and experimental results.

Computer Generated Holograms (CGHs) are useful for wavefront shaping and complex optics testing, including aspherical and free-form optics. Today, CGHs are recorded directly with a laser or intermediates masks but allows only recording binary CGHs; binary CGHs are efficient but can reconstruct only pixilated images. We propose to use a Digital Micro-mirror Device (DMD) for writing binary CGHs as well as grayscale CGHs, able to reconstruct fulfilled images. DMD is actually studied at LAM, for generating programmable slit masks in multi-object spectrographs. It is composed of 2048x1080 individually controllable micro-mirrors, with a pitch of 13.68 μm. This is a real-time reconfigurable mask, perfect for recording CGHs. A first setup has been developed for hologram recording, where the DMD is enlightened with a collimated beam and illuminates a photosensible plate through an Offner relay, with a magnification of 1:1. Our set up resolution is 2-3 μm, leading to a CGH resolution equal to the DMD micro mirror size. In order to write and erase CGHs during test procedure or on request, we use a photochromic plate called PUR-GD71-50-ST developed at Politecnico di Milano. It is opaque at rest, and becomes transparent when it is illuminated with visible light, between 500 and 700 nm; then it can be erased by a UV flash. We choose to code the CGHs in equally spaced levels, so called stepped CGH. We recorded up to 1000x1000 pixels CGHs with a contrast greater than 50, knowing that the material is able to reach an ultimate contrast of 1000. A second bench has also been developed, dedicated to the reconstruction of the recorded images with a 632.8nm He-Ne laser beam. Very faithful reconstructions have been obtained. Thanks to our recording and reconstruction set-ups, we have been able to successfully record binary and stepped CGHs, and reconstruct them with a high fidelity, revealing the potential of this method for generating programmable/rewritable stepped CGHs on photochromic materials.

With a growing interest in mid- and far-infrared astronomy using cooled imaging and spectrometer instruments in highaltitude observatories and spaceflight telescopes, it is becoming increasingly important to characterise and assess the spectral performance of cooled multilayer filters across the Q-band atmospheric window. This region contains spectral features emitted by many astrophysical phenomena and objects fundamental to circumstellar and planetary formation theories. However extending interference filtering to isolate radiation at progressively longer wavelengths and improve photometric accuracy is an area of ongoing and challenging thin-film research. We have successfully fabricated cooled bandpass and edge filters with high durability for operation across the 15-30 μm Q-band region. In this paper we describe the rationale for selection of optical materials and properties of fabricated thin-film coatings for this region, together with FTIR spectral measurements and assessment of environmental durability.